JVC HR-J430KR manual Recording, Engage TV Mode, Select Channel for Viewing, Reset Counter to Zero

Page 24

24

PLAYBACKANDRECORDINGFEATURES(cont.)

Recording

6

q

°5

Record One Program While Watching Another

1	ENGAGE TV MODE
	During recording...
	● If using the RF connection (☞ pg. 4), press TV/
	VIDEO. The VCR's VIDEO indicator goes out and the
	TV broadcast being recorded disappears.
	● If using the AV connection (☞ pg. 4), change the
	TV's input mode from AV to TV.

SELECT CHANNEL FOR

VIEWING

2 Use the TV’s channel selector to set the channel you want to watch.

OSD

1	2	3
4	5	6
7	8	9
C.RESET	0
C.RESET

Display Elapsed Recording Time

RESET COUNTER TO ZERO

1 Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs.

DISPLAY ELAPSED TIME ON SCREEN

2 During recording, press OSD at any time to see the elapsed time. All indications corresponding to the current status of the VCR are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.

●Make sure "SUPERIMPOSE" is set to "ON" (☞ pg. 17).

Image 24

Contents HR-J430KR Dear Customer Do not place the VCRContents Basic Connections Clock SET Date and TimeMake Corrections Tuner Perform Auto Channel SET Return to Normal ScreenAccess Tuner SET Screen Access AFC ScreenMake Selection Store Desired ChannelCode Setup Access Main Menu ScreenAccess Initial SET Screen Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Input Guide Channel NumberReturn to G-CODE SET UP Screen Input Receiving Channel NumberReturn to Normal Simple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Pause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow MotionActivate VARIABLE-SPEED Search Activate HIGH-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchEngage Manual Tracking Mode Adjust Manual TrackingRE-ENGAGE Automatic Tracking Manual TrackingAccess Function SET Access SuperimposeSuperimpose Access Distant Code Skip Over Unwanted SectionsStart Repeat Stop RepeatActivate Instant Review Activate CounterMemory Return to Counter Position ZeroTape Position Indicator Relation to B Beginning or E End shows you where you are onPress REW, then press Timer within 2 seconds Next-Function MemoryAccess B.E.S.T. Picture System Screen Select ModeS.T. Picture System PreparationRecording Press and hold RECQuality of the tape Use, then recording Begins with the picture Level optimizedPlayback Tape in useEngage TV Mode Reset Counter to ZeroRecording Select Channel for ViewingInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press RECCode Timer Programming Access G-CODE ScreenEnter G-CODE Number Engage Timer Mode CHECK/CORRECT InputData On-Screen Timer Programming Access ON-SCREENAccess Program SET Screen MenuSET Program Information ExampleDisengage Timer Cancel a ProgramRE-ENGAGE Timer Check And Cancel ProgramsAccess Auto SP/EP Auto SP/EP TimerPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OKAccess Auto Timer Auto TimerSpecial Features 19, 20Edit From a Camcorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Control Two JVC VCRsRandom As- semble Editing Prepare for EditingEND R.A. Edit Start R.A. EditTroubleshooting Cassette gets stuck partwayTimer again Re-perform the G-Code setup Doesn’t work properlyWhen scanning channels, some Has not been programmed correctly Cassette is automaticallyQuestions and Answers EIA monochrome signal Maximum recording time 210 min. with ST-210 video630 min. with ST-210 video Frequency-synthesized tunerRamdom Assemble Editing connector pg IndexRemote Control Provided Front Display PanelHR-J430KR