JVC HR-J430KR manual Code Timer Programming, Access G-CODE Screen, Enter G-CODE Number

Page 26
G-CODE
PRESS NUMBER KEY(0-9)
PRESS (MENU) TO MAIN MENU

26TIMERRECORDING

G-Code Timer Programming

Before G-Code Timer programming, see "G-Code Setup" on page 9.

OK

6

q

°5

 

1

2

3

NUMBER

4

5

6

 

7

8

9

CANCEL

 

0

 

 

 

 

TV/VCR

OK

MENU

ILLUMI GUIDE

During G-Code and on-screen timer programming, the Illumi- Guide feature tells you which button on the remote control must be pressed next by lighting it up. To use this feature, with the TV/VCR switch set to "VCR", press ILLUMI GUIDE before performing step 2. (MENU, REW, PLAY, FF light up at this time.)

If you aren't going to use the Illumi-Guide feature, go directly to step 1.

1

LOAD A CASSETTE

Make sure the record safety tab is present.

 

● The VCR’s power comes on automatically.

● If you’re watching on channel 3 or 4, press TV/VIDEO

 

to select the VIDEO mode. VIDEO is displayed on the

 

front display panel.

ACCESS G-CODE SCREEN

2 Press MENU on the remote control.

●The clock must be set in order to access the G- Code screen. If you

haven’t set the clock, the Main Menu screen appears when you press

MENU. Refer to page 5 for the clock setting proce- dure.

●If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys (0 – 9), CANCEL and MENU.

ENTER G-CODE NUMBER

3 Press the appropriate NUMBER keys to enter the G- Code number printed in the TV listings for the TV program you wish to record.

●To make corrections, press CANCEL and input the correct G-Code number.

●If the G-Code number you input is incorrect, "ERROR" may appear on the screen to advise you of the error. This happens when the G-Code number is for a program which has already passed. "ERROR" is displayed for about 4 seconds and the G-Code screen reappears (step 2).

●If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys (0 – 9), CANCEL and MENU.

When Using The Illumi-Guide Feature

●Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.

●If for some reason the remote control's signal is not received by the VCR, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HR-J430KR Dear Customer Do not place the VCRContents Basic Connections Make Corrections ClockSET Date and Time Tuner Perform Auto Channel SET Return to Normal ScreenMake Selection Access Tuner SET ScreenAccess AFC Screen Store Desired ChannelCode Setup Access Main Menu ScreenAccess Guide Channel SET Screen Access Initial SET ScreenAccess G-CODE SET-UP Screen Input Guide Channel NumberReturn to Normal Return to G-CODE SET UP ScreenInput Receiving Channel Number Find Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Still Picture/Frame-By- Frame Playback Pause During PlaybackActivate FRAME-BY Frame Playback Slow Motion/ Reverse Slow MotionVariable-Speed Search Reverse Play Activate VARIABLE-SPEED SearchActivate HIGH-SPEED Search High-Speed SearchRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Manual TrackingSuperimpose Access Function SETAccess Superimpose Start Repeat Access Distant CodeSkip Over Unwanted Sections Stop RepeatMemory Activate Instant ReviewActivate Counter Return to Counter Position ZeroPress REW, then press Timer within 2 seconds Tape Position IndicatorRelation to B Beginning or E End shows you where you are on Next-Function MemoryS.T. Picture System Access B.E.S.T. Picture System ScreenSelect Mode PreparationQuality of the tape Use, then recording RecordingPress and hold REC Begins with the picture Level optimizedPlayback Tape in useRecording Engage TV ModeReset Counter to Zero Select Channel for ViewingSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press RECEnter G-CODE Number Code Timer ProgrammingAccess G-CODE Screen Data Engage Timer ModeCHECK/CORRECT Input Access Program SET Screen On-Screen Timer ProgrammingAccess ON-SCREEN MenuSET Program Information ExampleRE-ENGAGE Timer Disengage TimerCancel a Program Check And Cancel ProgramsPlace the arrow next to Auto SP/EP Timer by Access Auto SP/EPAuto SP/EP Timer Pressing CH 5 or Push JOG 5, then press OKAccess Auto Timer Auto TimerSpecial Features 19, 20Edit From a Camcorder Load Cassettes SET RECORDER’S Input ModeEdit To Or From Another Control Two JVC VCRsRandom As- semble Editing Prepare for EditingEND R.A. Edit Start R.A. EditTroubleshooting Cassette gets stuck partwayWhen scanning channels, some Timer againRe-perform the G-Code setup Doesn’t work properly Has not been programmed correctly Cassette is automaticallyQuestions and Answers 630 min. with ST-210 video EIA monochrome signalMaximum recording time 210 min. with ST-210 video Frequency-synthesized tunerRamdom Assemble Editing connector pg IndexRemote Control Provided Front Display PanelHR-J430KR
Top Page Image Contents