Magnavox VRZ223AT owner manual Setting Up the VCR Plus+ Programming System cont’d

Page 33

VRZ223(H1690).QX33 4/9/99 9:09 AM Page 33

Setting Up the VCR Plus+ Programming System (cont’d) 33

2

Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. For stations whose VCR Plus+ and Cable/TV channels do not match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers by following steps 3 - 7. Make each entry within 60 seconds of the previous entry.

2 Examine the lists on page 32.

4-5

3

Press the VCR button, then press the MENU button.

4

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B

REPEAT PLAY OFF

ON SCREEN MODE LANGUAGE

VCR PLUS+ REF. MAP

TO END PUSH EXIT

5

Press the PLAY/o button or the STOP/p button to select VCR PLUS+ REF. MAP, then press the F.FWD/B button.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1 – – – – –> 1

22

TO SELECT CH PUSH op

THEN ENTER CH NO. TO END PUSH EXIT

7

3

6

POWER

VCR

 

TV

EJECT

1

2

 

3

VCR/TV

4

5

 

6

 

7

8

 

9

CHANNEL

 

 

VCR PLUS+

0

+100

 

SPEED

VOLUME

 

MUTE

MENU

STATUS/EXIT

CLEAR

MEMORY

REWIND

/PLAY

 

F.FWD

REC/OTR

/STOP

 

PAUSE/STILL

6

Look at the lists you filled in on page 32. For stations whose

VCR Plus+ and Cable/TV channels do not match, press the PLAY/o button or the STOP/p button until the arrow is beside the VCR Plus+ channel you need. Then, press the Number buttons to enter the corresponding Cable/TV channel from your list. (Enter a “0” before single- digit channels.) Enter all the stations on your list.

Note: If you are using a Cable Box/DBS, the Cable/TV channel will be 03 or 04 (the Cable Box/DBS output channel) for every VCR Plus+ channel. You must set the Cable Box/DBS to the channel you want to record; leave the Cable Box/DBS on for the timer recording.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1– – – – –> 23

22

TO SELECT CH PUSH op

THEN ENTER CH NO.

TO END PUSH EXIT

7

Helpful Hints

To erase a Cable/TV channel num- ber, repeat steps 3-5 on this page. Then, press the PLAY/o button or the STOP/p button to select it.

Press the CLEAR button, then press the STATUS/EXIT button.

To select line input for the Cable/TV channel, press 0,0. AUX will appear on-screen.

When you receive the VCR, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the same.

Press the STATUS/EXIT button.

Image 33
Contents VRZ223AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemANT Audio OUT Plug in the TV and the VCRHookups With a Cable Box / Direct Broadcast System ConnectionsRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAutomatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels613-4 Daylight-Saving Time Language Selection VCR Button Remote Control ButtonsVolume o/p Buttons Eject ButtonTV Button Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRecording Turn on the TV and set it to channel 3 or 4, whicheverVCR light does not appear, press the VCR/TV button once Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingInstructions continue on Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMPress the PLAY/o button or the STOP/p button to select Checking or Cancelling Timer RecordingsPROGRAM, then press the F.FWD/B button Program REVIEW, then press the F.FWD/B buttonChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Timer Recording With the VCR Plus+ Programming System cont’d Antenna Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Cable Box/DBS Output Channel 03 or GlossaryHelpful Hints Helpful Hints cont’d Specifications Video Cassette Recorder Limited WarrantyAutomatic IndexVRZ223H1690.QX33 4/9/99 910 AM Supplied Accessories