Magnavox VRC602M owner manual Press the VCR button, then press the Time Search but- ton

Page 37

Follow the steps below to program the VCR to search forward or backward on a tape a specific length of time. There must be a tape in the VCR.

1

Press the VCR button, then press the TIME SEARCH but- ton.

TIME SEARCH

0:00

ENTER SEARCH TIME

2

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5.

TIME SEARCH

0:05

PUSH FF OR REW

3

Within 10 seconds, press the F.FWD/B button or the REW(ind)/{ button. The VCR will skip over the specified length of time, then begin playback.

Time Search 37

EJECT

POWER

MENU STATUS/EXIT CLEAR

2	1	2	3
2	4	5	6
	7	8	9
	MEMORY		ALT.CH
		0
3	REC		PAUSE
	/OTR		/STILL
		PLAY
	REW	STOP	F.FWD
		STOP
	CH.		VOL.
		MUTE
	VCR	TV	CBL/DBS	1
	VCR/TV	SPEED	TIME SEARCH
		ENTER	SLOW

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 2.

•You can not do a Time Search while recording.

•To remove the Time Search display, press the TIME SEARCH button again.

•To cancel a Time Search that is in progress, press the STOP/p button.

Image 37

Contents VCR For Customer Use Warranty VerificationSafety Precautions FeaturesIntroduction Declaration of ConformityTable of Contents Battery Safety Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the power cords of the TV and the VCRConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’dHookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button, then press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single-digit number Setting the ClockPress the VCR button, then press the Menu button Daylight-Savings TimeLanguage Selection 2TV code Find your Setting the Remote to Operate a TV2code Find your Cable BOX CodesRemote Control Buttons TV Button CHannel o/p ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFFCassette Compartment VCR Display PanelRECord Light VCR LightFront Panel Rear Panel VHS Quasi Play Back Sqpb PlayingInsert a tape with its record tab intact in the VCR RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Press the VCR button, then press the Time Search but- ton Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemBlue Background Helpful Hints Helpful Hints cont’d Renewed Specifications Glossary / SpecificationsGlossary Automatic IndexSupplied Accessories