Magnavox VRC602M owner manual Helpful Hints

Page 44

44 Helpful Hints

If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself.

If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information appears on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative. If you believe the representative will need to help you with operations, please stay near the product. Our representatives will be happy to assist you.

No power

•Connect the power plug completely to an AC (alternating current) outlet.

•Turn on the power.

Power Failure

•The VCR may lose timer recordings, the clock and channel settings, and the language selection if the power fails. Follow the steps on pages 11 and 15 to reset the language, channels, and clock. Then, see pages 30-32 to reprogram your timer recordings.

The VCR will not record a TV program.

•Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable). Details are on pages six-10.

•Make sure the tape has a record tab. Details are on page five.

•Check the TV/VCR position. Details are on page 24.

•Check the CH3/CH4 switch. Details are on pages six-nine.

The VCR will not perform a timer recording.

•Make sure you set the recording start and stop times correctly. Details are on pages 30-33.

•Make sure a tape is in the VCR and the tape has a record tab (page five). If, after programming a timer recording, you turn off the VCR power without putting a tape in the VCR, the Timer light will blink.

•If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.

•Make sure the VCR power is off.

•Make sure you have set the clock correctly. Details are on page 15.

•The VCR may not perform or continue a timer recording if the power fails.

•If you have a Cable Box/Direct Broadcast System, you will program timer recordings differently. Details are on page eight.

•Finish programming a timer recording at least five minutes before the recording should begin.

•12 p.m. is noon; 12 a.m. is midnight.

There is no playback picture or the playback picture is noisy or contains streaks.

•Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch.

•Make sure the VCR is in VCR position. (The VCR light will appear on the display panel.)

•Adjust channel 03 or 04 at the TV.

•Adjust the tracking. Details are on page 39.

•TVs that are too close to the VCR can cause interference during tape playback. Move the VCR away from the TV.

The remote control will not operate the VCR.

•Press the VCR button, then try the other VCR feature buttons.

•Make sure the VCR light appears on the display panel. If it does not, press the VCR/TV button once.

•Aim the remote control directly at the VCR’s remote sensor. Details are on page 24.

•Remove all obstacles between the remote control and the VCR.

•Inspect and/or replace the batteries in the remote control. Details are on page five.

The Number buttons won’t work for channels above 69.

•Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter chan- nel numbers as a three-digit number. If you are using an antenna (not a cable signal), you may only select channels 2-69. Details are on page 20.

You cannot watch TV programs normally.

•Put the VCR in TV position, then change channels at the TV. (Press the VCR/TV button so that the VCR light disappears from the display panel. Details are on page 24.)

•Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable). Details are on pages six-10.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents VCR Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Battery SafetyUsing the Remote Control VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the power cords of the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups with a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Press the VCR button, then press the Menu buttonLanguage Selection Setting the Remote to Operate a TV 2TV code Find yourCable BOX Codes 2code Find yourRemote Control Buttons CHannel o/p Buttons TV ButtonOn-Screen Status Displays If you select Status ON, then select Counter only onIf you select Status ON, then select Counter only OFF If you select Status OFFVCR Display Panel Cassette CompartmentRECord Light VCR LightFront Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Insert a tape with its record tab intact in the VCRRecording One Channel/Watching Another One-Touch Recording Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select While the status display is on the screen, press Clear button to reset the real-time counter to zeroReal-Time Counter Memory Time Search Press the VCR button, then press the Time Search but- tonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onBlue Background Helpful Hints Helpful Hints cont’d Renewed Glossary Glossary / SpecificationsSpecifications Index AutomaticSupplied Accessories
Top Page Image Contents