Magnavox VRC602M Multi-Channel Television Sound System, Understanding On-Screen Displays

Page 40

40 Multi-Channel Television Sound System

Your VCR can play recordings broadcast in Hi-Fi (high fidelity) stereo, which produces a crisp, clear sound from two sources. Your VCR also can play tapes recorded in a second audio (usually, that means your program is recorded in a second language). Of course, your VCR will play tapes recorded in monaural (single-source) sound as well.

Your VCR also will record in Hi-Fi stereo or in second audio, so when you play that tape on the VCR, it will be in stereo or second audio.

Read the directions on this page to familiarize yourself with your VCR’s stereo and second audio setups. Then follow the directions on page 41 to record in stereo or second audio and the directions on page 42 to play tapes recorded in Hi-Fi stereo.

Understanding On-Screen Displays

When you receive a signal from a channel you’re watching, portions of the on-screen display shown below will appear when you press the STATUS/EXIT button on the remote control.

The indication 2ND AUD or TV STEREO that appears on this side of the status display tells you if your VCR is receiving a second audio or stereo broadcast. Although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time.

STOP		12:00 AM
TV STEREO		CH 02
		STEREO
		2ND AUD
SLP	1:23:45	HIFI

The indication 2ND AUD or STEREO that appears on this side of the status display tells you if the program you’re watching is available in second audio or stereo. This indication is not avail- able during tape playback.

Even though a program is available in stereo or second audio, you still must program the VCR to receive or record the program. Follow the directions on page 41.

To record and play programs broadcast in stereo, even if you have a single-speaker TV, just use one of the connections shown, then follow the steps on pages 41-42.

Stereo Amplifier

or Receiver

R

L

Audiocablesfrom AUDIO OUT Jacks of VCR to AUDIO IN Jacks

of Stereo Amplifier or Receiver

Single	Stereo	Monitor
Speaker TV	Speaker TV	TV

OR

OR

Monaural Sound

RF coaxial cable (supplied) from VCR’s

OUT Jack to TV’s ANTENNA IN Jack

OR

Video cable from VIDEO OUT Jack of VCR to VIDEO IN Jack of monitor TV

Image 40

Contents VCR Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Battery SafetyUsing the Remote Control VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the power cords of the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups with a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Press the VCR button, then press the Menu buttonLanguage Selection Setting the Remote to Operate a TV 2TV code Find yourCable BOX Codes 2code Find yourRemote Control Buttons CHannel o/p Buttons TV ButtonOn-Screen Status Displays If you select Status ON, then select Counter only onIf you select Status ON, then select Counter only OFF If you select Status OFFVCR Display Panel Cassette CompartmentRECord Light VCR LightFront Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Insert a tape with its record tab intact in the VCRRecording One Channel/Watching Another One-Touch Recording Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Time Search Press the VCR button, then press the Time Search but- tonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onBlue Background Helpful Hints Helpful Hints cont’d Renewed Specifications Glossary / SpecificationsGlossary Index AutomaticSupplied Accessories