Magnavox VRC602M owner manual Blue Background

Page 43

Blue Background 43

If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted.

Or, if you want to receive the weak signal, set BLUE BACK- GROUND to OFF. When you select a channel that is receiving a weak signal, you will see the static in the TV programming. The channel number will not appear on the screen when you select a weak channel, and you can not access the VCR’s status display.

Also, you may not be able to adjust the volume.1 To set BLUE BACKGROUND to ON or OFF, follow these

steps.

1

Press the VCR button, then press the MENU button.

SELECT op CHOOSE B

→PROGRAM VCR SET UP TUNER SET UP SET CLOCK

TO END PUSH EXIT

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B
→ REPEAT PLAY	OFF
ON SCREEN MODE
AUDIO OUT
LANGUAGE
BLUE BACKGROUND	ON
TO END PUSH EXIT

3

Press the PLAY/o button or the STOP/p button to select BLUE BACKGROUND. Then, press the F.FWD/B button repeatedly so that OFF (or ON) appears beside BLUE BACKGROUND.

SELECT op CHOOSE B

REPEAT PLAY	OFF
ON SCREEN MODE
AUDIO OUT
LANGUAGE

→BLUE BACKGROUND ON TO END PUSH EXIT

4

4 2-3

EJECT

POWER

MENU			STATUS/EXIT		CLEAR

1 2 3

4 5 6

7 8 9

MEMORYALT.CH

	0
REC	PAUSE
/OTR	/STILL

PLAY

REW F.FWD

STOP

CH.VOL.

	MUTE
VCR	TV	CBL/DBS
VCR/TV	SPEED	TIME SEARCH
	ENTER	SLOW

Press the STATUS/EXIT button.

Image 43

Contents VCR For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlBattery Safety Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the power cords of the TV and the VCRConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’dHookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button, then press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single-digit number Setting the ClockPress the VCR button, then press the Menu button Daylight-Savings TimeLanguage Selection 2TV code Find your Setting the Remote to Operate a TV2code Find your Cable BOX CodesRemote Control Buttons TV Button CHannel o/p ButtonsIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Light VCR Display PanelCassette Compartment RECord LightFront Panel Rear Panel VHS Quasi Play Back Sqpb PlayingInsert a tape with its record tab intact in the VCR RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Press the VCR button, then press the Time Search but- ton Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemBlue Background Helpful Hints Helpful Hints cont’d Renewed Specifications Glossary / SpecificationsGlossary Automatic IndexSupplied Accessories