Magnavox VRC602M owner manual Glossary / Specifications

Page 47

47 Glossary / Specifications

Glossary

AUDIO IN/OUT Jacks: jacks on the front and back of the VCR that record audio from another source (IN) or send audio to another system (OUT).

Automatic Channel Setup: process in which the VCR mem- orizes all available channels. Then, when you press the CH(annel) o/p buttons, you only scan through channels you receive.

Bands: settings that allow you to tune channels.

•Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69).

•Cable – all standard channels can be received without a Cable Box.

Cable Box/DBS Output Channel: 03 or 04.

Dubbing: copying a tape using a second VCR.

Frame: a still picture.

HQ: high quality; a feature in the VCR circuitry which provides enhanced picture detail.

Line Input: The channel to which you set your VCR during dub- bing. If you use the AUDIO and VIDEO In jacks on the front of the VCR, select channel 002 (AV FRONT). If you use the AUDIO and VIDEO IN jacks on the back of the VCR, select 001 (AV REAR). If you accidentally enter Line Input mode, press the CH(annel) o/p buttons or use the Number buttons to select another channel.

OTR: One-Touch Recording; a timed recording that starts immediately and records for 30 minutes to eight hours.

Remote Control: the small electronic unit that came with your VCR; allows you to operate your VCR from a distance.

RF coaxial cable: The black cable supplied with your VCR. Use it to connect your VCR to your TV (or Cable Box or DBS). The supplied cable is a snap-on type. However, you may use a screw-on type if you prefer.

Special Effects: forward and reverse searching; a still picture; slow motion playback.

Tape Speeds: how fast the tape travels during a recording or playback.

•SP (standard play) – fastest tape speed (recording time for a T120 tape is approximately two hours); best picture quality.

•LP (long play) – average tape speed; playback only.

•SLP (super long play) – slowest tape speed (recording time for a T120 tape is approximately six hours).

VCR: video cassette recorder.

VIDEO IN/OUT Jacks: jacks on the front and back of the VCR that record video from another source (IN) or send video to another system (OUT).

Specifications

Video Heads

Four heads - Hi-Fi

Video Signal

EIA standards; NTSC color

Antenna

VHF/UHF – 75 ohm external antenna terminal

VHF Output Signal

Channel 03 or 04 (switchable) 75 ohms unbalanced

Power Requirement

120V AC; 60Hz

Power Consumption

14W

Operating Temperature

41°F (5°C) to 104°F (40°C)

Relative Humidity

10% to 80%

Weight

5.3 lbs. (2.4 kg.)

Dimensions

14-3/16” (W) x 3-5/8” (H) x 8-1/2” (D) (360mm x 92mm x 215.5mm)

Tuner Broadcast Channels

VHF 2-13, UHF 14-69

Cable TV Channels

1-125

NOTE: Designs and specifications are sub- ject to change without notice.

Page 46 Page 48
Image 47
Page 46 Page 48
Contents VCR For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlBattery Safety Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the power cords of the TV and the VCRRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’dHookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button, then press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single-digit number Setting the ClockPress the VCR button, then press the Menu button Daylight-Savings TimeLanguage Selection 2TV code Find your Setting the Remote to Operate a TV2code Find your Cable BOX CodesRemote Control Buttons TV Button CHannel o/p ButtonsIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Light VCR Display PanelCassette Compartment RECord LightFront Panel Rear Panel VHS Quasi Play Back Sqpb PlayingInsert a tape with its record tab intact in the VCR RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select While the status display is on the screen, press Clear button to reset the real-time counter to zeroReal-Time Counter Memory Press the VCR button, then press the Time Search but- ton Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemBlue Background Helpful Hints Helpful Hints cont’d Renewed Glossary Glossary / SpecificationsSpecifications Automatic IndexSupplied Accessories
Top Page Image Contents