Magnavox VR602BMG, VR402BMG owner manual On-Screen Status Displays, Status Display example only

Page 20

20 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT but- ton or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

Whenever you press the STOP/p button or the PLAY/o button,

the status display will appear for five seconds. After five seconds, only the counter will remain on the screen. You must press the STATUS/EXIT button to remove it. Portions of the status display

Status Display (example only)

Receiving and Recording Mode (VR602BMG only)

also may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta- tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

Current status of tape

STOP

TV STEREO

Channel

Time

12:00 AM CH10

STEREO

2ND AUD

The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

SLP

M 1:23:45

HIFI

1

Tape

Speed

 

Press the MENU button.

 

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

Counter

Audio Out Mode

and

(VR602BMG only)

Counter

 

 

Memory

 

 

 

MTS

 

 

 

 

Broadcast

 

Available

 

(VR602BMG only)

SELECT op CHOOSE B

STATUS

[ON]

COUNTER ONLY

[OFF]

TO END PUSH EXIT

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

Helpful Hints

You may not access a status display when viewing a still picture, during slow motion playback, or during for- ward or reverse searching.

The status display may not appear if a weak channel is selected and BLUE BACKGROUND is set to OFF. Details are on page 41.

Image 20
Contents VCR Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Putting Batteries in the Remote ControlVCR maintenance Replace the battery compartment lidHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Cable Signal Cable Box/DBSRecording One Channel/Watching Another Hookups with a Stereo TV VR602BMGPress the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV VR602BMG only Automatic Channel SetupPress the Menu button Automatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock Enter a 0 before a single-digit numberDaylight-Savings Time Language Selection Press the STATUS/EXIT buttonRemote Control Buttons Channel o/p Buttons Remote Control Buttons cont’dClear Button On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Other playback options and features are on pages PlayingVHS Quasi Play Back Sqpb Read and follow the steps below to play a tapeVCR will record in a preset vol- ume RecordingInsert a tape with its record tab intact in the VCR VCR Light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Timer Recording cont’d Instructions continue onTape Speeds Checking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cablePress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Real-Time Counter Memory Time Search Press the Time Search buttonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Specifically…This indication is not available during tape playback MonitorMulti-Channel Television Sound System VR602BMG only cont’d Hi-Fi Stereo Sound System VR602BMG only Please see additional notes onBlue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Renewed Index Supplied Accessories
Related manuals
Manual 9 pages 10.87 Kb