JVC DR-MH200SE manual On The Front Display Panel, Link Functions

			INITIAL SETTINGS EN 19
Results Of Auto Set Up/Preset Download Appearing	INFORMATION
On The Front Display Panel	Language for the on-screen display
	Auto Set Up also selects the language automatically for the on-
If both Auto Channel Set and	screen display depending on the Country setting you have made in
	step 2 on page 17 (unless you have selected ABELGIUMB or
Auto Clock Set have been
	ASUISSEB), as shown below.
performed successfully, the
correct current time is displayed.	SUOMI	B SUOMI	ITALIA	B ITALIANO
Turn on the TV and select its AV mode, then make sure that all
	PORTUGAL	B ENGLISH	MAGYARORSZÁG	B ENGLISH
necessary stations have been stored in the unit’s memory by using
	DEUTSCHLAND	B DEUTSCH	ESPAÑA	B ESPAÑOL
the PR +/– button(s).
	POLSKA	B ENGLISH	NEDERLAND	B NEDERLANDS
● If station names (ID – A pg. 88) have also been stored in the
	NORGE	B NORSK	GREECE	B ENGLISH
unit’s memory, the station name will be displayed at the top right
	SVERIGE	B SVENSKA	OTHER WESTERN B ENGLISH
corner of the TV screen for about 5 seconds when the unit is
	DANMARK	B DANSK
tuned to a different station.
● If you want to set the tuner manually such as to add or skip	ÖSTERREICH	B DEUTSCH	OTHER EASTERN	B ENGLISH
channels, to change channel positions, or to set or change	ČESKÁ	B ENGLISH
station names, see pages 75 – 76.	REPUBLIKA
	If you want to change the language setting manually, see AOn-
If Auto Channel Set has
succeeded but Auto Clock Set	screen Language SetB (A pg. 20).
has not, APR 1B (channel	Just Clock
position) is displayed.	Your unit is equipped with the Just Clock function which provides
OR	accurate time keeping through automatic adjustments at regular
If both Auto Channel Set and Auto Clock Set have failed,	intervals, by reading data from a PDC signal. If you want to take
	advantage of this function, simply set it to AONB. (A pg. 77)
A– –:– –Bis displayed.
A Turn on the TV and select its AV mode, then make sure that all	T-V Link Functions
necessary stations have been stored in the unit’s memory by
using the PR +/– button(s).	When you connect the unit to your TV via a fully-wired 21-pin
● If station names (ID – A pg. 88) have also been stored in the	SCART cable (A pg. 16), the following functions are available. You
unit’s memory, the station name will be displayed at the top right	can use these functions only with a TV offering T-V Link, etc.*
corner of the TV screen for about 5 seconds when the unit is	For details, refer to the instruction manual of your TV.
tuned to a different station.	* Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK,
● If you want to set the tuner manually such as to add or skip	Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree
channels, to change channel positions, or to set or change	of compatibility and available functions may differ by system.
station names, see pages 75 – 76.	TV Auto Power On
B Perform AClock SetB (A pg. 77).	The TV will turn on and be set to its AV mode automatically
ATTENTION:	whenever you start playback.
After making sure the cables are connected properly, turn off the	For details, refer to the instruction manual of your TV.
unit’s power once, then turn the unit’s power back on again.	Unit Auto Standby
The Country Set display appears on the TV screen; perform AAuto	You can use your TV’s remote control to turn off the unit.
Set UpB (A pg. 17) or APreset DownloadB (A pg. 18) again.	For details, refer to the instruction manual of your TV.
IMPORTANT:	Direct Rec
● To check if the Guide Programme numbers have been set	You can easily start recording the programme that you are
correctly, perform the SHOWVIEW Timer Programming. (A pg. 45)	watching on your TV. When you use this function, set ADIRECT
● In certain reception conditions, station names may not be stored	RECB to AONB. (A pg. 71)

correctly, and auto Guide Programme Number Set may not work properly. If the Guide Programme numbers are not set properly when you timer record a TV programme using the SHOWVIEW system, the unit will record a TV programme of a different station. When programming the timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly.

(A pg. 45)

● Your unit memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture. (A pg. 75, ADelete A ChannelB)