JVC DR-M150SEK manual To Make The Disc For On-Disc Timer Programming, Press selection keys to

Page 39
DISC TIMER PRGM
PROG
PROGRAMME CHECK
DATE START STOP TV PROG DAILY/WEEKLY REC MODE
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++

Filename [M150SEK_07Timer Recording.fm]

 

M150SEK_00.book Page 39 Wednesday, June 15, 2005 4:04 PM

Masterpage:Right+

 

TIMER RECORDING EN 39

On-Disc Timer Programming

On-Disc Timer Programming is a function used with discs that are especially intended for a specific programme. The disc is then programmed for a programme you always watch every day or every week. Since older programmes are automatically overwritten, a single disc can be used without worrying about how much recording capacity remains. You can programme each disc to timer record as many as 8 programmes up to 30 days in advance.

●Make sure that the unit’s built-in clock is set properly.

●Turn on the TV and select an input mode such as EXT1.

●Load a DVD-RAM or DVD-RW (VR mode) disc for programming.

●Slide the TV/DVD switch to DVD.

ATTENTION:

●On-Disc Timer Programming is possible only with the disc for On-Disc Timer Programming.

●If data is recorded on a disc for On-Disc Timer Programming using a unit from another manufacturer, On-Disc Timer Programming may not function properly.

●If timer programming cannot be set or cancelled, wait for about 40 seconds and then try again.

To Make The Disc For On-Disc Timer Programming

1Press PROG to access

the Programme Check screen.

2 Press selection keys to select ADISC TIMER PRGMB, then press

ENTER.

● When some

 

DISC TIMER PRGM

programmes are

 

EXIT

OK

SELECT WITH [CURSORS]

recorded on the disc, a

 

SELECT

THEN PRESS [ENTER]

 

 

caution message

appears. You can either format the disc (A pg. 67) or insert a new disc, then re-perform the procedure from step 1.

●When On-Disc Timer Programming has already been made on the disc, press selection keys to select ANEW TIMER PROGRAMMEB, then press ENTER.

3Press selection keys to

set the desired date

(ADATEB), then press E.

4 Press selection keys to

DATE

START

STOP

TV PROG

 

set the desired start time

05/07 SAT

 

 

 

 

 

 

 

(ASTARTB), then press E.

DAILY/WEEKLY

REC MODE

 

● Each press of FG

NAME

WEEKLY

LP

 

increases/decreases the

 

 

 

 

 

 

start time in 1 minute

EXIT

CONFIRM SET TIMER PROGRAMMING WITH [CURSORS]

interval.

PROG

SELECT

THEN PRESS [ENTER]

 

●To increase/decrease the

start time in 30 minutes interval, press and hold FG.

TV DVD

DVD A

AUX

PROG

Selection Keys

(FGDE)

ENTER

5Press selection keys to set the desired stop time (ASTOPB), then press E.

●Each press of FG increases/decreases the stop time in 1 minute interval.

●To increase/decrease the stop time in 30 minutes interval, press and hold FG.

6Press selection keys to set the desired channel (ATV PROGB), then press E.

7Press selection keys to set ADAILY/WEEKLYB, then press E.

●For details on ADAILY/WEEKLYB setting, refer to ADaily/Weekly Recording FunctionB (A pg. 37).

8Set the other recording

options as required.

DISC TIMER PRGM

 

● ARecording ModeB

 

(A pg. 34)

DATE

START

STOP

TV PROG

● AModify Title NameB

05/07 SAT

18:30

20:30

YORN 1

(A pg. 46)

 

 

 

 

9 Press ENTER to access

DAILY/WEEKLY

REC MODE

NAME

WEEKLY

LP

 

 

 

the Programme

 

 

 

 

Confirmation screen.

EXIT

CONFIRM SET TIMER PROGRAMMING WITH [CURSORS]

10 Press ENTER to

PROG

SELECT

THEN PRESS [ENTER]

 

 

 

 

 

complete ATo Make The Disc For On-Disc Timer ProgrammingB.

●To programme another timer using ATo Make The Disc For On- Disc Timer ProgrammingB, repeat steps 1 - 10.

11 Press DVD A to turn off the power.

● is displayed on the front display panel.

●To disengage the timer mode, press DVD A again.

Satellite Receiver Users

To timer record a satellite broadcast using On-Disc Timer Programming:

APerform On-Disc Timer Programming.

●In step 6, press AUX to set ATV PROGB to ASATB. Then press FG to enter the channel position for the satellite broadcast.

BSet the satellite receiver to the appropriate channel for recording.

●Leave the satellite receiver’s power on.

Page 38 Page 40
Image 39
Page 38 Page 40
Contents DR-M150SEK Filename M150SEK02Safety.fm Safety PrecautionsInformation for Users on Disposal of Old Equipment Some Do’s And Don’ts On The Safe Use Of Equipment Information On Reception Of Digital TransmissionsAbove ALL Contents DVD-R/RW Discs About DiscsRecordable/Playable Discs DVD-RAM DiscsDiscs For Playback Only Unplayable DiscsRegion Number DVD-R Recording Medium And FormatFile Structure Of Discs DVD-RAMPlacing a Disc DVD Video MarksRecording side Maintenance of discsCare And Handling Of Discs Label sideFront View Rear ViewProgramme Buttons PR +/-A pg Front Display Panel Remote Control For switching the input of a JVC TVTV/VIDEO Button Check Contents When pressing REC Mode When using Live Memory playbackWhen playing back a recorded title When recordingAscart Videob Press selection keys to select Aauto SEARCHB, then press Auto Set UpAuto Channel Set/Auto Clock Set Before starting, make sure of the followingDisplay Panel Language Monitor SetMenu/Audio/Subtitle Language Set Setting Favourite Mode Setting DTVSetting The Subtitle Language Setting The Audio LanguageDisplaying The Subtitles Adjusting The VolumeBasic Operation TV Selecting The Desired ChannelBasic Playback Top menu Playback FeaturesVariable Speed Search Still Picture/Frame-By-Frame PlaybackSkip Search When Aresumeb is set to Adisc ResumebResume Function Slow MotionAngle Selection Checking The Time InformationSubtitle Selection On-Screen Display Audio Channel SelectionPlayback Control PBC Function Track USERecording stops Live Memory PlaybackRecording screen Live CheckLive Memory Playback Simultaneous Recording and PlaybackTo watch from the recording start point Navigation Available only when pausedBasic Operation On The On-screen Bar Using The On-screen BarHow To Access The On-screen Bar Contents of the on-screen bar during playbackDuring Playback Locating The Beginning Of a Desired SelectionDVD-RAM/RW/R Audio CD/Video CD/SVCD/JPEG/MP3Normally select this Setting The Progressive ModeSelect this option when too much noise appears Time SearchWhile stopped Select The Switching Interval Of The Slide ShowRandom Playback Programme PlaybackBasic Recording Recording ModeElapsed Recording Time And Disc Remaining Time Indication Recording FeaturesInstant Timer Recording ITR UnitFree Rate Function DiscDisc space Daily/Weekly Recording Function Number keys entrySatellite Receiver Users Manual Timer ProgrammingOn-Disc Timer Programming To Make The Disc For On-Disc Timer ProgrammingPress selection keys to Programmed Disc How Discs Are OverwrittenWhen Programmes Overlap Each Other Recording Automatic Satellite ProgrammeIcons and their meanings About registration of informationLimitations of registration IndexDelete Title Play Back TitleTo modify the points Modify Category Edit Original InformationModify Index Modify Title NamePlay Back Play List Create Play List Delete Play ListPlay List Edit Play List Information Modify Play List NamePress selection keys to select ASAVEB, then press Enter Press Navigation to Delete Scenes Move ScenesCreated play list to Add ScenesPress selection keys to select AEDITINGB, then press Enter To move to other titles Press S or TRegister Disc Delete InformationScan For Title From Library After all the files are played back Locating The Desired Group And TracksPress Navigation Press selection keys to select AMP 3B or AJPEGB, then pressAuto capture button Sound monitor switchDV Dubbing DV dubbing controllerExample Dubbing to an MD When you dub from DV equipment other than a camcorderDigital Audio Dubbing To skip unwanted part of the source pictureIf the camcorder has no S-VIDEO output connector If the camcorder has an S-VIDEO output connectorEdit From a Camcorder When using your unit as the recording deck When using your unit as the source playerOutput And L-1 Input Setting Output/Input SetRGB / Component Select Setting Input Setting2 Select VIDEO/RGB / S-VIDEO/RGB /SAT VIDEO/RGB Connecting To a Satellite Receiver Mode Set You can change the brightness of the front display panel To record in Dolby Digital formatTo record in Linear PCM format To turn off superimposed indicationsSet the TV brand code Remote Control FunctionsTV Multi-Brand Remote Control Remote Control 1/2/3/4 Code SwitchingTV Brand Code Table Scan Mode SetTray Lock Child LockTuner Set Auto Channel SetManual Channel Set Set Stations Setting FavouritesConfirming Images Of Registered Channels Delete a ChannelClock Set Just ClockSelection keys to set AVR Modeb Format a DiscFormat a DVD-RAM Disc Format a DVD-RW DiscAfter finalising For DVD-R/RW Video mode discs Finalise a DiscFinalise a DVD-R/RW Disc Recording InitialisingGeneral PlaybackTimer Recording Other ProblemsPower failure occurred Set date and time correctly. a pg During Live Memory playback, o has been pressed. a pg Timer recording has finished during Live Memory playbackLanguage Code List Dimensions WxHxD Power requirementPower consumption TemperatureAudio Language/Sound Selection Check, Cancel And Change ProgrammesSelect The Switching Interval Of The Slide Show When Programmes Overlap Each Other June 15, 2005 404 pmMemo EN DR-M150SEK
Top Page Image Contents