Tascam RC-898 owner manual Memory and batteries

Page 17

Section 3.5 - Memory and batteries

3.5 Memory and batteries

As you have noticed, the RC-898 requires no power supply of its own, drawing its power from the DTRS units to which it is connected.

Location memories and configuration settings are stored using a battery backup system. The battery should provide power for several years of use.

When the battery eventually degrades to the point where it cannot provide enough power to retain settings, the message Memory Error will be shown on the diaply screen (this can be removed by pressing the ESCAPE key).

When this message appears, all memories (loca- tion memories and configuration settings) are cleared and reset to the default settings.

If you see this message, contact your TASCAM dealer for details of battery replacement. Do not attempt to replace the battery by yourself.

3-3

Image 17

Contents RC-898 For U.S.A RC-898 features Table of Contents IntroductionConnections Menu and basic operationsExternal control and settings Table of Contents Making settings on the Dtrs unitsTimecode functions Menu and parameter referenceKey features Key featuresIntroduction UnpackingPrecautions and recommendations Precautions and recommendationsBattery backup Digital audio cablesReference clock in a digital studio AccessoriesAccessories Accessories RC-898 features Front panel Lock Status indicators Machine number indicators Through 6, E1, E2Vari indicators Time Mode indicatorsData INC/DEC key and indicator Preset keyRepeat key and indicator Front panel ENTER/LOAD keyRear Panel Contrast Rear Panel DIP switches 1Connection to Dtrs units ConnectionsConnection to Dtrs units Machine IDsConnections RS-422 Units Connections parallel unitsConnections parallel units Connections GPI event unitsMemory and batteries Memory and batteriesMemory and batteries Navigation Menu and basic operationsNavigation Invalid operationsFast setting of values Resetting values to zeroSetting values using the Value display Data entryCommonly-used menus Selecting the unit controlled by the menusStoring and recalling user setups Storing and recalling user setupsRecalling menus using the function keys Saving the current setupRecalling a user setup or restoring factory settings Storing and recalling user setups Transport controls Basic Dtrs operationsSelecting the unit to which operations refer Formatting tapesMonitoring Shuttle modeMonitoring Arming tracksShuttle muting Shuttle monitoringMonitoring Monitoring flowchart DA-88 and DA-38 Monitoring Monitoring tablesMonitoring Setting a relative time reference Setting the precisionLocation functions Reference modesABS setting ABS settingSelecting Time Mode Return-to-zeroLocation operations Setting the location pre-roll valueLocation operations Auto playEditing a location Manual entry of a location pointStoring the location in a memory Recalling a location memoryRepeating a section Repeating a sectionRepeated entry of location points Editing a location memoryPunch operations Crossfade times Performing the punch recording Setting pre-roll and post-roll timesRehearsing the punch recording Punch operations Track delay Making settings on the Dtrs unitsTrack operations Track operationsUnit-related functions Key ModeUnit-related functions Rec Mute functionAuto Offset function Chasing with an offsetClock selection Checking the offsetOutput timing From menu group E, move the cursor to eitherInput selection Varispeed pitch controlWord length DitherReference levels Unit-related functions Confidence modeMeter modes Sine oscillatorN e O s c i l l a t o r C h i n e Unit-related functions Primary timecode functions Timecode functionsPrimary timecode functions Selecting the timecode sourceSelecting a timecode type Setting the generator start timeRecording the timecode on a Dtrs timecode track Checking the generator progressRewind the tape to the beginning Start the timecode sourceChasing with a timecode offset Chasing to external timecodeAdvanced timecode functions Independent clock settingsAdvanced timecode functions Auto Timecode Offset functionRechase mode Error bypassSynchronization of timecode Pull up and pull downPark position Fast LTCMidi Timecode output Play the master unit Individual recording status while chasing timecodeVideo resolve D e o R e s o l v e C h i n e O f f E e Advanced timecode functions Controlling GPI devices External control and settingsControlling the parallel port device Controlling the serial port 9-pin Controlling the serial port 9-pinSelecting the serial port device Location pre-roll on the serial unitSerial unit timing source Split mode on the serial unitControlling recording operations on the serial unit Use the UP and Down keys to select between Split and NormalOther Dtrs control functions Other Dtrs control functionsChoosing a control protocol Track mapping functionsTimecode track mapping Recording delayRemote track arming Device emulationMMC ID Fast wind speedCue-up tally D I / B u s I D C h i n e C e i v e Other Dtrs control functions Menu group Menu and parameter reference Menu groupsMenu groups GPI Time value to Timecode type Output All parameters On, off 7, Midi Time Fast wind mode Menu group E Menu group aMenu group F Alphabetical list of menu items Alphabetical list of menu itemsSpecifications SpecificationsDimensions Dimensions Dtrs Index A-EABS 6-2,8-2 Index F-OIndex P-T Generator 8-1,8-2,10-5,10-6 Index U-ZRC-898