Daewoo DF-4501P user manual Connectionsi, CH52, Corresponding scart socket at the back of a

Page 10

Connectionsi

•There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of the connections described below. Whichever TV connection you use will work with all input sources.

•Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best connections.

•For better sound reproduction, connect the DVD Recorder+VCR’s AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo, or audio/video equipment. See ‘Connecting an Amplifier/Receiver‘ on page 13.

Caution

•Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.

•Do not connect the DVD Recorder+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.

•Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connections

Connecting a TV

Choose one of the following TV connections, depending on the capabilities of your equipment.

RF Connection

Connect the RF OUT (TO TV) jack on the DVD Recorder+VCR to the antenna in jack on your TV using the supplied

 

75-ohm RF cable (R). If you use this connection, tune your TV to the DVD Recorder+VCR's RF output channel

CONNECTIONS

(CH52).

 

 

 

 

 

Scart Connection

 

Rear of TV

 

 

 

 

 

VIDEO

ANTENNA

COMPONENT/PROGRESSIVE VIDEO INPUT

 

S- INPUT

INPUT

1 Plug a scart cable into the scart socket EURO AV1 at

Pr

Pb

Y

 

 

 

 

 

 

 

the back of the DVD Recorder+VCR and the

 

 

 

 

 

corresponding scart socket at the back of the TV set.

C

 

S

 

 

 

(V)

 

V

R

 

 

 

 

 

 

 

2 Plug a scart cable into the blue scart socket EURO

 

 

 

 

 

 

AV2/DECODER at the back of the DVD Recorder+VCR

 

 

 

 

 

 

and the corresponding scart socket at the back of a

 

 

 

 

 

 

Connecting Antenna/Cable

 

1 Disconnect the antenna/cable from the rear of your TV.

Antenna

2 Connect this cable to the jack marked ANT IN (FROM ANT.) on the rear panel of the DVD Recorder+VCR.

Flat Wire (300ohm)

OR

300/75ohm Adapter (Not supplied)

Antenna

Cable TV

Wall Jack

OR

 

satellite decoder or set top box.

 

S-Video Connection

 

1

Connect the S-VIDEO OUT jack on the DVD

Rear of DVD Recorder+VCR

 

Recorder+VCR to the S-Video in jack on your TV using

 

 

 

an S-Video cable (S).

 

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables.

Component Video Connection

1Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding input jacks on your TV using a Y Pb Pr cable (C) if the Component Video jacks (Y, Pb, Pr) are available on your TV.

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables.

Rear of DVD Recorder+VCR

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT IN (FROM ANT.) jack on the rear panel of the DVD Recorder+VCR.

Use the supplied coaxial cable to connect between the DVD Recorder+VCR’s OUT (TO TV) jack and the antenna input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels (all cable channels).

Progressive Scan Connection

•If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD Recorder+VCR’s Progressive Scan output for the highest video resolution possible.

•If your TV does not accept the Progressive Scan format, the picture will appear scrambled.

1Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using an optional Y Pb Pr cable (C).

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the supplied audio cables.

•Be sure to set the DVD Recorder+VCR to Progressive Scan mode by pressing and holding [P.SCAN] for 3 seconds (or changing the Video Output in the Setup Menu; see page 23).

•Progressive Scan does not work with the RF, Audio/Video or S-Video connections.

12

 

 

 

13

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DVD Recorder + VCR Precautions Safetyty InstructionsI t tiAlcohol- based cleaning agents For your own SafetyAvoid direct exposure to beam ImportantI t t SafeguardsUnit leave all servicing to qualified service personnel All operating and use instructions should be followedTable of Contents Overviewi Number of this player, the disc cannot be playedSurface of the unit To obtain a clear picture To clean the cabinetTo keep the surface clean Nearest dealerIdentification of Controls Recording Pause mode Standby modeOTR Recording mode Selects VCR mode Selects DVD modeConnect to a TV or other equipment with audio inputs Plug into a power outletRecover from system down Connect to a TV with Component Video Y Pb Pr inputsCorresponding scart socket at the back of a ConnectionsiCH52 Satellite decoder or set top boxConnecting Optional Equipment Connecting an Amplifier/ReceiverConnecting a Digital Camcorder DV model only Go to page 17~28 Go to page 47~49 Initial InstallationInitial Setup Go to page 50~52 Go to page 42~44Enter the date and time Select the PR number you want to edit using …/† Press SETUP. The Setup menu appearsFollow the same procedure as the ‘DVD Record Quality’ ‘Recording Options’ SettingsUse œ and √ to select ‘Language Follow the same procedure as the OSD LanguageDisplays Press √. The ‘Video‘ submenu is displayedPress √. The ‘Audio‘ submenu is displayed No signal will be output from the Digital Audio Out jacksWhile ‘Preferences Use …/† to select the desired digital output typeUse …/† to select ‘VCR‘ Password then press EnterConfirm, press Enter Press Enter to display the submenuOn-Screen Displayi l Overviewverview You can change the TV audio using the Audio button DVD PlaybackConfirm Track Interval won’t be displayed in PBC on modeZoom function may not work on some DVDs VCR Playbackl To return to normal playback, press PlayPrepare a CD which includes both MP3 and Jpeg files Other Disci PlaybacklInsert the CD and play an MP3 file Follow the instructions below to record a TV program Basicic RecordingiDVD Recorder can play DivX files on CD-R/RW Make sure your TV input is set to view the DVD Recorder+VCRTo stop copying at any time, press Stop Insert the VHS videotape you wish to copy into the VCR deckInsert a blank VHS videotape into the VCR deck During one touch copy you can search and resume copyTimer Recording using Manual Set Record Screen Timer Recording‘Timer Recording’ menu appears Timer Recording using ShowView VideoPlus systemOnly one Timer recording will work You should set only one Timer RecordingRecording from an Externalxternal InputInput Disc Operation in DVD±RW disc Disc OperationDisc Initialize Erase the disc DVD±RWIf you want to adapt the whole disc, press Enter Use …/† to select ‘Finalize’ menuUse …/† to select ‘Adapt’ menu Press …/† to select ‘Disc Info’Press Enter to change the title name Select ‘Label’ using … †Disc Edit Character or function and press EnterTroubleshooting Finalized disc Discs recorded with copy-once No solution Made compatible if using aNo solution Your TV’s tuner Timer Recording notTechnicali l Specificationsi i ti
Top Page Image Contents