Magnavox 1VMN26713A owner manual Troubleshooting, Remedy

TROUBLESHOOTING

Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.

	Remedy
The power does not turn on.	• Check that the AC power cord is connected securely.
	• Check the breaker (in case of power failure).
	• Press [TIMER SET] to cancel the timer standby mode.
There is no picture.	• Re-connect the connecting cords securely.
	• Check if the connecting cords are damaged.
	• Check the connection to your TV (pages 15-20).
	• Switch the input selector on your TV (such as to “L1”) so that the signal
	from the unit appears on the TV screen.

TV program reception does not fill the	• Try to set the channels with “Auto Channel Preset” or “Manual Channel
TV screen.	Preset” in “Channel” menu (pages 28-29).
	• Select a channel of any TV program using [CHANNEL / ].
TV program pictures are distorted.	• Adjust TV antenna.

•Adjust the picture. (Refer to the TV’s instruction manual.)

•Place the unit and TV farther apart.

•Place the TV and any bunched RF coaxial cables farther apart.

	TV channels cannot be changed.	• Switch the input to TV.
		• Connect the RF coaxial cable correctly (pages 15-20).
	There is no sound or the sound is	• Re-connect all connections securely.
	distorted.	• Check if the connecting cord is damaged.
		• Check the connections to the amplifier input.
GENERAL		• Check if the input device setting on the amplifier is correct.
		• When the unit is in pause mode or in slow-motion playback mode,
		sound is not output. This is not a malfunction.
		• When the unit is in fast forward or fast reverse mode, sound is not
		output. This is not a malfunction.
		• While the setup menu or timer programming display is shown, or while
		the screen saver is active, the audio is muted.
	The remote control does not function.	• Batteries are weak.
		• There are obstacles between the remote control and the unit.
		• The remote control is far from the unit.
		• There are no batteries in the remote control.
		• Check if the unit is turned on.
		• Check if you are pointing the remote control at the recorder and NOT the TV.
		If you have a plasma TV, it may interfere with the IR signal. Try the
		remote with the plasma off. If the remote works, you may need to move
		the unit away from the plasma TV.
		• Press [DVD] or [VCR], whichever you need. Then, try again.
		• Press [TIMER SET] to cancel the timer standby mode.
	Time jumps/Auto Clock set’s incorrect	• Set the “Auto Clock Setting” to “OFF” on page 30-31 and try “Manual
	time.	Clock Setting” on page 32.
	The unit does not operate properly.	• When static electricity, etc., causes the unit to operate abnormally,
		unplug the unit and then plug it in again.
	No analog TV closed captions are	• If you are using HDMI connection to watch the TV programs through
	output.	this unit, analog TV closed caption cannot be output. Try using another
		output connection to the TV.
	Playback picture is distorted.	• Keep devices which may cause electrical disturbances, such as a cellular
		phone, etc away from unit.
	The channel cannot be changed from	• Set the TV’s input to “TV.”
	the channel you are recording.
VCR	Nothing was recorded even though	• There was a power failure during recording.
	you set the timer setting correctly.	• The unit’s internal clock stopped due to a power failure that lasted for
•		more than 30 seconds. Reset the clock (pages 30-32).
DVD		• The program contains copy protection signals that restricts copying.
		• The timer setting overlapped with another setting that has priority.
	Timer recording is not complete or did	• The timer setting overlapped with another setting that has priority (page 46).
	not start from the beginning.	• Disc space was not enough.
	Timer recording is impossible.	• Make sure	appears on the front panel display of this unit. If not, press
		[TIMER SET].

EN 97

Introduction Connections Basic Setup Recording Playback Editing Function Setup VCR Functions Others

Español