Grizzly g0747, g0748 owner manual Power Feed Test Run, To test the power feed

Page 26

Power Feed Test Run

The mill comes with a power feed unit for X-axis table travel. Proper operation of the limit switch attached to the front middle of the table is criti- cal for the safe use of this power feed unit. If the power feed does not operate as expected during the following steps, disconnect it from power and contact our Tech Support at (570) 546-9663 for assistance.

To test the power feed:

1.Make sure all tools, cables, and other items are well clear of table movement as you fol- low these steps.

2.refer to the X-Axis Power Feed section, beginning on Page 28, to understand how the power feed, table locks, and limit switch function.

3.loosen the table locks on the front of the table.

4.plug the power feed power cord into a grounded 110V power outlet.

-24-

5.Make sure the power feed direction knob is in the neutral (middle) position, turn the speed dial counterclockwise to the lowest setting, then press the ON button.

6.turn the direction knob to the left, slowly turn the speed dial clockwise to increase the speed, then confirm that the table is moving to the left.

7.Watch for the table limit stop to hit the limit switch and turn the power feed OFF, stopping the table movement.

8.turn the direction knob through the neutral (middle) position and all the way to the right. The table should begin moving to the right.

9.Confirm that the table stops moving when the limit stop presses against the limit switch plunger.

10.Move the direction knob to the neutral (mid- dle) position, turn the speed dial to the lowest setting, and press the OFF button.

Congratulations! The Test Run of the mill is complete. Continue to the next page to per- form the Spindle Break-Inand Adjustments & Inspections procedures.

Model G0747/G0748 (Mfg. Since 8/12)

Image 26
Contents For models manufactured since 8/12 Page Table of Contents Wiring Contact Info IntroductionMachine Description Manual Accuracy Front View Identification Model G0747 Headstock Identification Model G0748 Headstock Identification Machine Data Sheet Main Specifications Operation Info Model G0748 Vertical Mill Variable Speed Variable Safety Safety Instructions for MachineryPage Additional Safety for Milling Machines Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftUnpacking SetupNeeded for Setup Inventory Small Item Inventory Figure QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations To lift and move the mill Lifting & PlacingHEAVy Lift Bolting to Concrete Floors Leveling & MountingLeveling Machine MountsTo assemble the mill AssemblyInitial Lubrication Test Run Mill Test RunPower Feed Test Run To test the power feedSpindle Break-In Inspections AdjustmentsTo perform the spindle break-in procedure Operations Operation OverviewTable Locks Table MovementGraduated Index Rings Axis Power Feed Identification Head Movement Axis Power Feed OperationTo operate the X-axis power feed Tool Needed QtyTilting Head Forward/Backward Rotating Head Left/RightRotating Ram Ram MovementMoving Ram Forward/Backward Recommended Cutting Speed FPM x Spindle SpeedDetermining Spindle Speed Tool Diameter in inches xSetting Model G0747 Spindle Speed To set the Model G0747 spindle speedLow Spindle Speed Range Setting Model G0748 Spindle Speed To set the Model G0748 spindle speedSpindle Downfeed Downfeed ControlsTo use the coarse downfeed Coarse DownfeedFine Downfeed Auto-Downfeed To use the auto-downfeedSpindle Brake Model G0747 brake lever G0748 Brake LeverUnloading Tooling Loading/Unloading ToolingLoading Tooling Tools Needed QtyAccessories G1076-52-PC. Clamping KitG7155-6 Precision Milling Vise G9299-10 Yuasa-Type Rotary TableSchedule MaintenanceCleaning Protecting Lubrication QuillTable Ways One-Shot Oiler Headstock GearingTable Elevation Leadscrew Ram WaysHead Tilt & Ram Pinions Power Feed Gears To lubricate the power feed gearsMachine Storage Symptom Possible Cause Possible Solution ServiceTroubleshooting Symptom Possible Cause Possible Solution Adjusting Gibs Saddle gib and adjustment screw Knee Gib Adjustment ScrewAdjusting Leadscrew Backlash Axis Leadscrew BacklashCross Leadscrew Backlash Tramming Spindle To tram the spindle to the tablePage Wiring Wiring Safety InstructionsG0747 Wiring Diagram G0748 Wiring Diagram Parts MainMain Parts List DescriptionAxis Leadscrews DescriptionDownfeed System Downfeed System Parts List CAM ROD Sleeve Assembly G0747 Headstock G0747 Headstock Parts List PFH30M Flat HD SCR M5-.8 XG0748 Headstock G0748 Headstock Parts List Headstock Front COVER, Aluminum One-Shot Oiler Accessories G0747 Machine Labels & Cosmetics G0748 Machine Labels & Cosmetics Model G0747/G0748 Mfg. Since 8/12 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns