Multi-Tech Systems MT2834ZDX manual Removing Your Old Modem from Windows, Install the Modem Driver

Page 6

Chapter 1 – Introduction and Installation

Step 3: Install the Modem Driver

If you use Windows 98+, you must install the modem driver, which is installed using the Windows Plug and Play feature. Follow the four-step procedure below. If you use another operating system, see the Appendix.

1.Make sure your modem is connected properly, and then turn on your computer. Windows should detect your new modem and open the Install New Modem wizard.

2.Insert the system CD, and then click OK.

3.Windows installs and configures the modem.

4.Click Finish to exit.

For Windows NT, the Install New Modem wizard presents one additional prompt before Step 2. At this prompt, select: Don’t detect my modem; I will select it from a list, and then click Next.

A dialog box with a list of manufacturers and a list of modem models appears. Select your modem. Continue with Step 2 above.

Note: If Windows cannot identify your modem (for instance, if it identifies your modem as a “Standard Modem”), click Change. A dialog box with a list of manufacturers and a list of modems appears.

Step 4: Install Data Communications Software

Data communications software is designed to send and receive messages. Multi-Tech includes PhoneTools communications software with your modem. However, the modem will work with most data communications software. To install PhoneTools, insert the CD into the CD-ROM drive; click the PhoneTools icon. You will be asked to choose your language. The software automatically loads onto your PC.

Removing Your Old Modem from Windows

When a new modem replaces another modem, the old modem installation remains in Windows after you install the new modem, and the old modem is still selected in HyperTerminal and other Windows applications. Although you can change the application connection descriptions one at a time, it is easier to force Windows applications to use the new modem by removing the old modem from Windows.

1.Click the Start button, point to Settings, and click Control Panel.

2.Double-click the Modems icon to open the Modems Properties dialog box.

3.In the list box, select the old modem.

4.Click Remove, then click Close.

5.The next time you dial a HyperTerminal connection, it will select your new modem and ask you to confirm the selection.

Multi-Tech Systems, Inc. MT2834ZDX User's Guide

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents MT2834ZDX-Series External Data/Fax Modem Users Guide User Guide MT2834ZDX-Series S000309A Rev. a Copyright Contents Features Introduction InstallationSafety Warnings Getting StartedModem Installation Attach the Self-Adhesive FeetConnect the Modem to Your System Install the Modem Driver Install Data Communications SoftwareRemoving Your Old Modem from Windows Speed Indicator Blink Rates OperationFront Panel AT Commands, S-Registers Result Codes AT CommandsCarrier Detect Control $BAn Baud AdjustDCn AT Command Control CDn Cleardown at DisconnectEn Non-Error Correction Mode Flow Control En Echo Command Mode CharactersEn V.42 Error Correction Modes DPn Read Line Probe Data$Fn Enable/Disable Auto-Reliable Fallback Character $En V.42 Error Correction at 300 bpsLoad Default Configurations Fn Echo Frequency Canceller Offset Compensation$H n Help Screens List Commands#L n V.42 Mode Selection in Originate Mode Inquire Product CodesNd Dial a Stored Number Result Codes Enable/Disable$MBn Modem Baud Rate NdNe. .. Number LinkingRDn Square Wave Ring Detect Rn Clear to Send ControlRAn Asymmetrical Bit Rate RFn CTS/RTS Interaction Control$SBn Serial Port Baud Rate Tn Respond to Remote Digital Loopback SignalSFn DSR/CD Interaction Control Tone-DialReturn to Command Mode Wn Store ConfigurationModem Reset Xn Result Codes and Call Progress SelectionAtcr Remote Configuration Escape Sequence +++ATCR Escape CodeBreakatcr Escape Sequence Register Unit Range Default Description RegistersResult Codes Terse VerboseTroubleshooting None of the LEDs Light When the Modem Is OnModem Dials But Cannot Connect Modem Disconnects While Online There Are Garbage Characters on the Monitor Appendix a Regulatory Compliance Regulatory ComplianceCFR Part 15 Regulation CFR Part 68 Telecom Current Requirements for Label Content and Format USAAAEQ##TxxxxRegulatory Requirements for Canada Industry Canada IC XXXXXX-ZZZZZZZZ WhereManual Control Power switch Appendix B Technical SpecificationsCommand Buffer 60 characters Transmit Level -13 dBm Frequency Stability +/-0.01%Appendix C Warranty and Service WarrantyOnline Warranty Registration About the Internet Index AtcrModem driver installation
Related manuals
Manual 34 pages 22.61 Kb
Top Page Image Contents