QS206
FRONT PANEL
1 2 3
1 2 3 4 5
MENU
EXIT
6 7 8 9 0
QS206
16CH H.264 Digital Video Recorder
|
|
|
|
|
4 | 5 | 6 |
HDD REC ALM FULL NET
OK
7 | 8 | 9 |
REAR PANEL
1
|
|
|
|
|
|
| VIDEO IN |
|
|
|
|
|
| ||
1 | 2 | 3 | 4 | 5 | 6 |
|
| 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 |
|
|
|
|
|
|
|
|
|
| AUDIO IN | AUDIO | CVBS OUT | 16 | 15 | |
DC +12V | VGA | RJ45 | USB | 1 2 3 4 | GND5 COM1 NO1 COM2 NO2 GND | GND | GND +12V GND |
|
| ||||||
|
| OUT |
|
|
|
| |||||||||
IN |
|
|
| ALM IN |
|
|
|
|
| ||||||
2 | 3 | 4 | 5 |
| 6 |
|
|
|
| 7 | 8 |
| 9 |
|
|
Item # | Name/ Symbol | Description |
|
|
|
|
|
1 | STANDBY | Press to set the system in standby mode. Press again to wake. | |
|
|
|
|
2 | MENU/EXIT | Press to open/close the main menu. | |
|
|
|
|
3 | CHANNEL/ | Press the number buttons to view the selected channel full- | |
| NUMBERS | screen; press buttons | |
|
|
|
|
4 |
| ▲ | Press to move cursor up; in PTZ mode, press to pan |
|
| camera up. | |
|
| ▼ | Press to move cursor down; in PTZ mode, press to |
| NAVIGATION | pan camera down. | |
| ◄ | Press to move cursor left; in PTZ mode, press to pan | |
|
| ||
|
| camera left. | |
|
| ► | Press to move cursor right; in PTZ mode, press to |
|
| pan camera right. | |
5 | LED | Shows status of hard drive, recording, alarm, HDD full and | |
| INDICATORS | network. |
|
|
|
| |
6 | IR SENSOR | IR Receiver for remote control. | |
|
|
| |
7 |
| In menus, press to confirm selections; in PTZ mode, press to | |
| OK | change the navigation buttons to control a connected PTZ | |
|
| camera (not included) | |
|
|
|
|
8 |
| ◄◄ | Increase reverse playback speed 1X, 2X, 4X. |
|
| n/► | Press to freeze playback to one frame, then press |
| DURING | again to advance | |
| ► | Press to start playback | |
| PLAYBACK | ||
|
| ||
| PRESS: |
| |
| ►► | Press to slow playback speed by 1/2, 1/4, 1/8. | |
|
| ||
|
| ►► | Press to increase forward playback speed 1X, 2X, |
|
| 4X. | |
9 |
| USB | Connect a USB flash drive for data backup and |
|
|
| firmware upgrades |
|
|
|
|
Item # | Connector | Description | |
|
|
| |
1 | VIDEO IN | Video input for connecting analog video signal input (BNC) | |
|
|
| |
2 |
| DC 12V/3A Power Connection | |
|
|
| |
3 | VGA OUTPUT | To connect to VGA monitor | |
|
|
| |
4 | NETWORK | For connecting Ethernet cable | |
|
|
| |
5 | USB | Mouse port | |
|
|
| |
| ALARM INPUT | 8 I/O Alarm input | |
|
|
| |
| ALARM | I/O Output for alarm | |
| OUTPUT | ||
6 |
| ||
|
| ||
RS485 | RS485 for connecting PTZ | ||
| |||
|
|
| |
| +12V | Power supply for DC relay, the current is 100MA (to prevent | |
| short circuits) | ||
|
| ||
|
|
| |
7 | AUDIO IN | Audio input for connecting audio signal (2 feeds) | |
|
|
| |
8 | AUDIO | For connection to amplified speaker | |
OUTPUT | |||
|
| ||
|
|
| |
9 | VIDEO OUT | Video output for connecting TV (BNC) | |
|
|
|
12 | 13 |