Q-See QS4474 user manual QS408, Front Panel Rear Panel

Page 8

QS408

FRONT PANEL

REAR PANEL

1

 

 

2

 

3

4

5

1

 

2

3

 

4

 

5

 

 

 

 

 

 

QS408

HDD

REC

ALM

FULL

NET

 

ON/OFF

 

 

AUDIO IN

 

AUDIO

 

VIDEO IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

 

3

 

 

 

 

 

1

3

5

7

1

3

5

7

 

 

 

 

 

 

 

 

 

 

 

USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

4

5

 

6

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

-

+

 

 

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

 

9

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

4

6

8

2

4

6

8

 

 

 

1 2 3 4 5 6 7 8

 

 

 

 

 

 

 

DC +12V

RJ45

VGA

 

 

VIDEO

 

 

 

+12V

GND 485B

485A

GND NO COM GND

ALARM IN

 

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

7

 

 

8

 

9

6

7

8

 

 

9

 

 

 

 

 

 

10

Item #

Name/ Symbol

Description

 

 

 

 

 

1

STANDBY

Press to set the system in standby mode. Press again to wake.

 

 

 

 

2

LED

Shows status of hard drive, recording, alarm, HDD full and

 

INDICATORS

network.

 

3

 

Press to move cursor up; in PTZ mode, press to pan

 

 

camera up.

 

 

Press to move cursor down; in PTZ mode, press to

 

NAVIGATION

pan camera down.

 

Press to move cursor left; in PTZ mode, press to pan

 

 

 

 

camera left.

 

 

Press to move cursor right; in PTZ mode, press to

 

 

pan camera right.

4

 

◄◄

Increase reverse playback speed 1X, 2X, 4X.

 

 

n/

Press to freeze playback to one frame, then press

 

DURING

again to advance frame-by-frame.

 

Press to start playback

 

PLAYBACK

 

 

 

PRESS:

 

 

►►

Press to slow playback speed by 1/2, 1/4, 1/8.

 

 

 

 

►►

4X.Press to increase forward playback speed 1X, 2X,

5

IR SENSOR

IR Receiver for remote control.

 

 

 

6

MENU/EXIT

Press to open/close the main menu.

 

 

 

7

CHANNEL/

Press buttons 1-8 to view that channel full-screen

 

Press buttons 1-0 (“0” is located next to the playback buttons) to

 

NUMBERS

 

input passwords and user IDs.

 

 

 

 

 

7

 

In menus, press to confirm selections; in PTZ mode, press to

 

OK

change the navigation buttons to control a connected PTZ

 

 

camera (not included)

 

 

 

 

9

 

USB

Connect a USB flash drive for data backup and

 

 

 

firmware upgrades

 

 

 

 

Item #

Connector

Description

 

 

 

1

Power Switch

Power On/Off

 

 

 

2

USB

Mouse port

 

 

 

3

AUDIO IN

Audio input for connecting audio signal (8 feeds)

 

 

 

4

AUDIO

For connection to amplified speaker

OUTPUT

 

 

 

 

 

5

VIDEO IN

Video input for connecting analog video signal input (BNC)

 

 

 

6

 

DC 12V/3A Power Connection

 

 

 

7

NETWORK

For connecting Ethernet cable

 

 

 

8

VGA OUTPUT

To connect to VGA monitor

 

 

 

9

VIDEO OUT

Video output for connecting TV (BNC)

 

 

 

 

ALARM INPUT

8 I/O Alarm input

 

 

 

 

ALARM

I/O Output for alarm

 

OUTPUT

10

 

 

 

RS485

RS485 for connecting PTZ

 

 

 

 

 

+12V

Power supply for DC relay, the current is 100MA (to prevent

 

short circuits)

 

 

 

 

 

14

15

Image 8
Contents Model QS434 About this Manual Table of Contents Introduction Features and Specifications Installation ConnectionItem # Connector Description QS206Front Panel Rear PanelQS408 Front Panel Rear PanelQS434 During Playback Press Item # Name/ Symbol DescriptionQS464 QS4474 Controls ControlsMouse Control Virtual KeyboardRemote Control Name/Symbol FunctionPower ON/OFF System LoginBasic Operation Shortcut MenuBasic Settings Symbol Name FunctionBasic Operation Main MenuPassword Admin and User passwords must not be the sameOperation DATE/TIMEDisplay VIDEO/AUDIOBOTTOMLEFT, Topright PreviewHard Drive HDD Management PlaybackVideo Search Formatting the Internal Hard DriveUsing the ON-SCREEN Playback Controls File ListTo narrow search results NavigationBackup Using the Playback SoftwareVideo Play Settings Audio SettingsRecording Configuration RecordingRecording Recording ScheduleMotion Detect Motion Detection SettingsMask Field Alarm Settings Advanced FeaturesAlarm Advanced Features Restoring Factory Settings Restarting the DVR SOFT-RESETConfiguring a PTZ camera PAN-TILT-ZOOM Cameras PTZHard Drive Installation Product SpecificationsAppendix QS206 QS408 QS434 QS464 QS4474Frequently Asked Questions Question 11 Why is Motion detection not working? See Product Warranty Liability ExclusionsQuestions or COMMENTS? Contact US