Energy Speaker Systems LTV46DA manual Connecting to Cable Reception, Connecting to Headphones

Page 13

Connections and Start of Operation

Connecting to Cable Reception

1 Plug the coaxial cable of the cable reception into the socket [ANT].

Connecting to Headphones

The output for the headphone is on the right rear side of the unit. If you connect a headset to the unit, the main speaker will be switched off.

Connecting Camcorders and Video Games

You can use the television set to connect camcorder and video games. Use either the cinch sockets or one of the SCART sockets.

➣Connecting Camcorders and Video Games by AV Cable

English

1Connect the AV cables according to the colours (red/white/yellow) to the sockets [VIDEO/AUDIO IN] and the output sockets of the external devices.

Image 13

Contents LTV46DA Page Content Reduce Noise Channel Groups Disposal ConformitySafety Unpacking and SetupUnit Remote control Batteries Mains cable Scope of SupplyUnpacking and Setup Intended purpose LocationFront View Viewing the Control PanelsRear View Remote Control Connecting to two Devices with Scart Socket Connecting to a Device with Scart SocketConnections and Start of Operation Connections for TV ReceptionConnecting to a Device without Scart Socket Connecting to the Roof AerialConnecting to Headphones Connecting to Cable ReceptionConnecting Camcorders and Video Games Connecting Camcorders and Video Games by AV CableConnecting Camcorders and Video Games by Scart Cable Connecting Camcorders and Video Games by S-Video CableWith the output sockets of the external devices Connecting to External Devices with Component Input Connecting to a ComputerAV 3 or AV 4 on the television set Connecting Several Devices Connecting the Digital Audio OutputConnecting Mains Cable Connecting to the Hdmi ConnectionInserting the Batteries Connecting HDMI/DVI CableSwitching On SettingsSwitching Off Setting up for OperationStarting Automatic Tuning TV Stations TuningOpen, Select and Close Menus PressUse this function to set the channel for individual stations Change channelSet System Set Colour SystemPress . To return to the main menu, press Several times Fine Tuning Manual TuningUse this function to tune the channels manually Change Channel Name Sound SettingsUnit can record and play back stereo sounds Press or Select NameUse this function to improve poor signal quality Improve Signal QualityPress Select Install or Adjust the settings Press to save the settingsChannel Groups Reduce NoiseWatch Favourite Channel Use this function to reduce picture noiseSet Aspect Ratio Set Screen LanguageSet Wide Screen Format Display if no Wide Screen Signal is Received Set Picture ModeSet Individual Colour Channels Additional Picture SettingsPress to open the desired menu Adjust Individual Audio Frequencies Audio SettingsSet volume Set BalanceIs a registered trademark Adjust Medium and Low FrequenciesSet Sound Source Enter the time using the key pad Press to save the settingsSet Time Use this function to set a time when the unit turns on Set Switch on TimeSet Time by Station Press Select on or OFF orAutomatic Switch off Set Switch off TimeAutomatic Switch off if no Signal is Received Use this function to set a time when the unit turns offSet On-Screen Display Switch Off if no Key is PressedSet Duration Set Transparency Child LockActivate Child Lock Settings for the Computer Restore DefaultPress Press the mains switch on the back of the unit Set Characters for TeletextWatching Set VolumeWatch Current Television Program Select Source Recall a Favourite ChannelSelect Input Press Press repeatedly until you select the desired channelWatch Two Programs at the Same Time PIP Set Picture-in-Picture Position Set Picture-in-Picture SizeTeletext Use this function to set the size of the small pictureAdjust Picture Size while Watching Set Picture Mode while WatchingStill Picture Show TimeSet Sound while Watching Set Sound Effect while WatchingSet Stereo/Mono while Watching Use this function to set the sound effectsCleaning and Troubleshooting See chapter Restore Default on Cast in black and white. Adjust the colour settingsCheck wether the connecting cable is properly connected to Cannot be displayed. Change the settings in the computerPixel Type Technical specificationsPb/Pr 1360 xMemo Memo Memo