Energy Speaker Systems LTV46DA Connecting the Digital Audio Output, Connecting Several Devices

Page 16

Connections and Start of Operation

Connecting the Digital Audio Output

You can Connect optical digital audio cable to "DIGITAL AUDIO OUT" on the rear of the TV and the other end to "DIGITAL AUDIO IN" of the equipment with a digital output to enjoy digital sound (Multi-Channel Surround Sound, Stereo, Dolby Sound).

1Connecting the OPTICAL Port

Connect the OPTICAL port of the DIGITAL

AUDIO OUT on the rear of the TV to the optical audio input of the DVD Home Theater System (or AV Receiver Amplifier) using the optical cable.

2 Connecting the COAXICAL Port Connect the COAXIAL port of the DIGITAL AUDIO OUT on the rear of the TV to the coaxial audio input of the DVD Home Theater System(or AV Receiver Amplifier)using the coaxial cable.

Decrease the TV volume to enjoy the more clear and grand sound through separate speakers.

Refer to corresponding user's manual from the manufacturer for connecting the speaker to the DVD Home Theater System or AV Receiver Amplifier.

Connecting Several Devices

You can use the connections described parallel . On how to select the desired source see “Select Source” on Page 36 and “Select Signal Source for PIP” on Page 37.

Connecting Mains Cable

1 Connect the mains cable.

Connecting to the HDMI Connection

This can be applied if there is the HDMI Output connector on the external device.

What is HDMI (High-Definition Multimedia Interface)?

HDMI is a next generation interface that connects the digital audio and video signals using only one cable without compression. The sound signal supports multi-channel (5.1 Channel). So it is called a multimedia interface rather than a video terminal. The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) and supports multi channel audio.

14

Image 16
Contents LTV46DA Page Content Reduce Noise Channel Groups Conformity DisposalUnpacking and Setup SafetyUnit Remote control Batteries Mains cable Scope of SupplyUnpacking and Setup Location Intended purposeFront View Viewing the Control PanelsRear View Remote Control Connecting to a Device with Scart Socket Connecting to two Devices with Scart SocketConnections and Start of Operation Connections for TV ReceptionConnecting to the Roof Aerial Connecting to a Device without Scart SocketConnecting to Cable Reception Connecting to HeadphonesConnecting Camcorders and Video Games Connecting Camcorders and Video Games by AV CableConnecting Camcorders and Video Games by Scart Cable Connecting Camcorders and Video Games by S-Video CableWith the output sockets of the external devices Connecting to External Devices with Component Input Connecting to a ComputerAV 3 or AV 4 on the television set Connecting the Digital Audio Output Connecting Several DevicesConnecting Mains Cable Connecting to the Hdmi ConnectionConnecting HDMI/DVI Cable Inserting the BatteriesSettings Switching OnSwitching Off Setting up for OperationTuning Starting Automatic Tuning TV StationsOpen, Select and Close Menus PressChange channel Use this function to set the channel for individual stationsSet System Set Colour SystemPress . To return to the main menu, press Several times Fine Tuning Manual TuningUse this function to tune the channels manually Sound Settings Change Channel NameUnit can record and play back stereo sounds Press or Select NameImprove Signal Quality Use this function to improve poor signal qualityPress Select Install or Adjust the settings Press to save the settingsReduce Noise Channel GroupsWatch Favourite Channel Use this function to reduce picture noiseSet Aspect Ratio Set Screen LanguageSet Wide Screen Format Set Picture Mode Display if no Wide Screen Signal is ReceivedSet Individual Colour Channels Additional Picture SettingsPress to open the desired menu Audio Settings Adjust Individual Audio FrequenciesSet volume Set BalanceAdjust Medium and Low Frequencies Is a registered trademarkSet Sound Source Enter the time using the key pad Press to save the settingsSet Time Set Switch on Time Use this function to set a time when the unit turns onSet Time by Station Press Select on or OFF orSet Switch off Time Automatic Switch offAutomatic Switch off if no Signal is Received Use this function to set a time when the unit turns offSet On-Screen Display Switch Off if no Key is PressedSet Duration Set Transparency Child LockActivate Child Lock Restore Default Settings for the ComputerPress Press the mains switch on the back of the unit Set Characters for TeletextWatching Set VolumeWatch Current Television Program Recall a Favourite Channel Select SourceSelect Input Press Press repeatedly until you select the desired channelWatch Two Programs at the Same Time PIP Set Picture-in-Picture Size Set Picture-in-Picture PositionTeletext Use this function to set the size of the small pictureSet Picture Mode while Watching Adjust Picture Size while WatchingStill Picture Show TimeSet Sound Effect while Watching Set Sound while WatchingSet Stereo/Mono while Watching Use this function to set the sound effectsCleaning and Troubleshooting Cast in black and white. Adjust the colour settings See chapter Restore Default onCheck wether the connecting cable is properly connected to Cannot be displayed. Change the settings in the computerTechnical specifications Pixel TypePb/Pr 1360 xMemo Memo Memo