SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
(Safety Decals continued from previous page) |
|
| LOADER MOUNTING INSTRUCTIONS | ||||
|
|
|
|
|
| ||
6 - PN 56050 |
|
|
| Read Operator’s Manual instructions before proceding. | |||
|
|
|
| To Remove Loader |
| ||
|
|
|
|
|
|
| |
| WARNING |
| WARNING | 1. | Park tractor on level surface with bucket flat on | ||
|
|
| ground. |
| |||
|
|
|
|
|
|
| |
|
|
|
|
| 2. | Dump bucket to take weight off mount pins and | |
|
|
|
|
|
| allow for stand installation. Set brake and shut off | |
|
|
|
|
|
| tractor. |
|
|
|
|
|
| 3. | Remove stands from crosstube and pin into brackets. | |
|
|
|
|
|
| (Pin location noted in mounting manual.) |
|
|
|
|
|
| 4. | Remove mount pins from loader upright. |
|
|
|
|
|
| 5. | Roll back bucket completely to raise uprights from | |
CRUSHING HAZARD |
|
|
|
| mounts. |
| |
|
|
| 6. | Shut off engine. Disconnect hydraulics. Back tractor | |||
| To avoid injury |
| FALLING HAZARD |
| away. Store mount pins in loader uprights. |
| |
|
|
| To Mount Loader |
| |||
or death: |
| To avoid injury |
|
| |||
| 1. Remove mount pins from uprights. |
| |||||
| Do not walk or work un- |
|
| ||||
| or death: |
| 2. | Drive tractor into loader slowly. |
| ||
derneath a raised loader. |
| 3. | Shut off tractor. Connect hydraulics. |
| |||
| Lower loader to ground |
| Do not work from or |
| 4. | Dump bucket to lower upright into mounts. |
|
|
| allow riders on loader or |
| ||||
| before leaving tractor |
| 5. | Continue dumping bucket until uprights settle into | |||
|
| its attachments. |
| ||||
| seat. |
|
| mounts, pins can be installed and stands can be | |||
|
|
|
| ||||
|
|
|
|
|
| removed. Set brake and shut off tractor. |
|
|
|
|
|
| 6. | Install mount pins and clips. Remove stands and pin | |
5 - PN 19924 |
|
|
|
| into crosstube. | ||
|
|
|
|
| |||
|
|
|
|
|
| ||
9 - PN 56059 | |
WARNING |
|
Check for leaks with cardboard; never use hand.
Before loosening fittings: lower load, release pressure, and
be sure oil is cool.
Consult physician immediately if skin penetration occurs. |
8 - PN 45002 (WHEN EQUIPPED)
WARNING
LOADER ATTACHMENT CAN FALL OFF IF NOT PROPERLY ATTACHED.
Read operator’s manuals for instructions. Position and align loader to attachment.
Rotate coupler handles to full locked position. Lockpins must fully extend and engage into attachment retaining slots.
Attachment mechanism must be functional and in good repair.
Only use loader manufacturer approved attachments.
For information on approved attachments, call
Failure to follow these instructions can result in serious injury or death.
7 - PN 56055
11 - PN 45024
WARNING
Only use loader manufacturer approved attachments. |
|
Failure to do so can cause serious injury or death. | |
|
10 - PN 56889
(WHEN EQUIPPED)
56889 |
8 - PN 260274
(WHEN EQUIPPED
MAN0063 (Rev. 12/15/00) | SAFETY 5 |
| |
|
|