Emerson EWC19T5 Automatic Clock Setting, To Cancel the DAYLIGHT-SAVING Time, CH Search

08 10 13

_ _

AUTOMATIC CLOCK SETTING

Make sure ...

•The unit must be turned on.

•Confirm the unit is receiving a RF (Radio Frequency) signal from either an antenna or cable system connection using the ANT. jack on the rear of the unit.

NOTES:

• If a cable converter box is being used, make sure it is powered on.

• You must use the remote control to perform the clock setting procedure.

• If the unit is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself and the unit must be set to the output channel of the cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct the clock automatically.

1 Select “SETTING CLOCK”

Hit [SETUP].	- TV/VCR SETUP -
	TIMER PROGRAMMING
Press [K / L] to select	B SETTING CLOCK
	CHANNEL SET UP
	USER’S SET UP
“SETTING CLOCK”, then hit	V-CHIP SET UP
	LANGUAGE [ENGLISH]
[ENTER] .	CAPTION [OFF]
	ZERO RETURN
	TIME SEARCH
	INDEX SEARCH
2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –
	B AUTO CLOCK	[ON]
Hit [ENTER] to select [ON].
	AUTO CLOCK CH SEARCH
	AUTO CLOCK CH	[ 02 ]
	MANUAL CLOCK SET
	D.S.T.	[OFF]

3Begin “AUTO CLOCK CH SEARCH”

Hit [L] to select “AUTO CLOCK	– SETTING CLOCK –
CH SEARCH”.	AUTO CLOCK	[ON]
	B AUTO CLOCK CH SEARCH
Then hit [ENTER].
	AUTO CLOCK CH	[ 02 ]
• The unit begins searching for the	MANUAL CLOCK SET
station which contains the auto	D.S.T.	[OFF]

clock set signal. The search for a

signal may take up to 20 seconds per channel.

•When the search has ended, “_ _” – AUTO CLOCK CH SEARCH –

appears at the lower left of the screen.

•Write down the number(s) that

appear on the screen. They are the auto clock station(s) in your area.

•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 18.

4Enter the channel number that contains the Automatic Clock Setting Signal

Hit [RETURN] to go back to “SETTING CLOCK”
menu.	– SETTING CLOCK –
Hit [L] to select “AUTO CLOCK	AUTO CLOCK	[ON]
	AUTO CLOCK CH SEARCH
CH”.
	B AUTO CLOCK CH	[ 45]
	MANUAL CLOCK SET
Press [s / B] until you locate Auto	D.S.T.	[OFF]

Clock Set station number.

5 Exit the setting clock mode Hit [SETUP] to exit the menu.

NOTE:

•Once the unit is turned off, it will periodically check and set the correct date and time.

DAYLIGHT-SAVING TIME

TV/VCR

Select this feature and the unit’s clock automatically will advance one hour in April, then reverse one hour in October.

When Daylight-Saving Time is ON, the clock will change automatically as follows:

•First Sunday of April : At 2 AM the clock immedi- ately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record.

•Last Sunday of October : At 2 AM the clock immediately changes to 1 AM.

Make sure ...

• The unit must be turned on.

1 Select “SETTING CLOCK”	TIMER PROGRAMMING
	- TV/VCR SETUP -
Hit [SETUP].	B SETTING CLOCK
	CHANNEL SET UP
Press [K / L] to point to “SET-	USER’S SET UP
	V-CHIP SET UP
	LANGUAGE [ENGLISH]
TING CLOCK”, then hit [ENTER].	CAPTION [OFF]
	TIME SEARCH
	ZERO RETURN
	INDEX SEARCH

2Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press [K / L] to point to “D.S.T.”,

then hit [ENTER] until [ON]	– SETTING CLOCK –
	AUTO CLOCK	[ON]
appears.	AUTO CLOCK CH SEARCH
	AUTO CLOCK CH	[ 02 ]
	MANUAL CLOCK SET
	B D.S.T.	[ON]

NOTE:

•During AUTO CLOCK CH SEARCH, the picture may be distorted.

3Exit the Daylight-Saving Time mode

Hit [SETUP] to exit the menu.

TO CANCEL THE DAYLIGHT-SAVING TIME

Repeat steps 1 to 2 and select [OFF] using [ENTER].

- 19 - EN