Magnavox CCZ130AT Turning On the TV/VCR, You cannot set up channels if you are using a Cable Box

Page 8

CCZ130comb 4/5/99 7:32 PM Page 8

8 Turning On the TV/VCR

Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly.

The instructions on this page work only when you turn on the TV/VCR for the first time.

1

Press the POWER button. The TV/VCR will come on and the screen shown below will appear.

SELECT LANGUAGE

> ENGLISH

ON

ESPAÑOL

SELECT KL OR

PRESS MENU TO CONTINUE

2

Press the PLAY/K button or the STOP/L button to select

English or Spanish on-screen displays.

3

Press the MENU button. The screen shown below will appear.

CONNECT ANTENNA OR CABLE

TO TVCR

THEN PRESS B

TO END PRESS EXIT

4

Press the FF/SEARCH B button to begin automatic chan- nel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on- screen briefly. Then the TV/VCR will go to the lowest channel programmed.

(If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on- screen. Connect an antenna or cable to the TV/VCR, then try again. You may need to follow the steps on page 10 instead.)

5

Use the CHANNEL o/p buttons or the Number buttons on the remote control to select a TV/VCR channel. Use the VOLUME o/pbuttons to adjust the sound.

3

 

 

 

 

 

1

POWER

MENU

STATUS/EXIT

CLEAR

 

 

1

2

3

MEMORY

 

 

4

5

6

 

 

5

7

8

9

CHANNEL

 

 

 

 

0

+100

ALT.CH

 

 

 

 

SLEEP

 

 

VOLUME

MUTE

 

SPEED

4

2

REW/SEARCH

 

PLAY/

FF/SEARCH

REC/OTR

 

STOP/

PAUSE/STILL

Helpful Hints

•If you do not see any on-screen dis- plays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages nine - 10 to select a language and set up channels.

•To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Channels will not be set up, and CHANNELS NOT SET will appear on-screen briefly.

•You cannot set up channels if you are using a Cable Box.

•Line Input mode will always be stored in the TV/VCR’s memory as channel 00. When you select chan- nel 00, A/V IN will appear on- screen briefly. Press the CHANNEL o/p buttons or Number buttons to select another channel.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CCZ130AT Dear Philips Magnavox product owner For Customer UseIntroduction FeaturesSafety Precautions Table of Contents Before Using the TV/VCR Rod Antenna Hook up your TV/VCR using one of the connections shownHooking Up The TV/VCR Hooking Up The TV/VCR cont’d Crooked Pin Straight PinYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRLanguage Selection Press the Menu buttonAutomatic Channel Setup Wait for the TV/VCR to set up channelsCHANNEL, then press the FF/SEARCH B button Adding/Deleting ChannelsPress the PLAY/ button or the STOP/ button to select Setting the Clock Manual Clock SettingSetting the Clock cont’d Automatic PBS Channel Selection Wait for the TV/VCR to find the time Manual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Daylight-Saving Time Press the Menu buttonTime Zone Front Panel ANTenna Jack AC Power CordRear Panel Remote Control Buttons STATUS/EXIT Button Menu ButtonMemory Button Channel o/p ButtonsAdjusting the Picture Controls Adjusting the Picture Controls cont’d Decrease IncreaseMore brilliant SofterOn-Screen Status Displays If you select Status ON, then select Counter only OFFIf you select Status ON, then select Counter only on If you select Status OFFReminder ReminderPlaying Recording Recording options are on pages 30One-Touch Recording Press the RECord/OTR button repeatedly untilRerecording Tape Duplication Different brands of equipment may operate differentlyTimer Recording DailyTimer Recording cont’d Instructions continue onPlease see page 48 for more Helpful Hints Checking or Clearing Timer Recordings Defeat Recording REC DefeatedSetting the Sleep Timer Closed Caption ExampleMenu ScreenClosed Caption cont’d Standard Closed CaptionsVolume Bar Repeat Play B Repeat Play Insert a tape in the TV/VCR Press the Menu buttonPress the STATUS/EXIT button to remove the display. a Press the Memory button to set the start position aReal-Time Counter Memory Automatic Operation Features Playback Options Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureSpecifications GlossaryHelpful Hints Helpful Hints cont’d Limited Warranty TV/VCR CombinationIndex ControlsSupplied Accessories
Top Page Image Contents