Magnavox CC13B1MG Turning On the TV/VCR, You cannot set up channels if you are using a Cable Box

Page 8

8 Turning On the TV/VCR

Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly.

The instructions on this page work only when you turn on the TV/VCR for the first time.

1

Press the POWER button. The TV/VCR will come on and the screen shown below will appear.

SELECT LANGUAGE

> ENGLISH

ON

ESPAÑOL

SELECT KL OR

PRESS MENU TO CONTINUE

2

Press the PLAY/K button or the STOP/L button to select

English or Spanish on-screen displays and menus.

3

Press the MENU button. The screen shown below will appear.

CONNECT ANTENNA OR CABLE

TO TVCR

THEN PRESS B

TO END PRESS EXIT

4

Press the FF/SEARCH/B button to begin automatic chan- nel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on the screen briefly. Then the TV/VCR will go to the lowest channel programmed.

(If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on the screen. Connect an antenna or cable to the ANT(enna) jack on the TV/VCR, then press the FF/SEARCH/B button again. You may need to follow the steps on page 10 instead.)

5

Use the CHANNEL K/L buttons or the Number buttons on the remote control to select a TV/VCR channel. Use the VOLUME K/L buttons to adjust the sound.

3

 

 

 

 

 

1

POWER

MENU STATUS/EXIT

CLEAR

 

 

1

2

3

MEMORY

 

5

4

5

6

 

 

7

8

9

CHANNEL

 

 

 

 

0

 

ALT.CH

 

 

 

 

SLEEP/WAKE UP

 

2

VOLUME

MUTE

 

SPEED

4

REW/SEARCH

PLAY/

 

FF/SEARCH

REC/OTR

STOP/

 

PAUSE/STILL

Helpful Hints

•If you do not see any on-screen dis- plays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages nine-10 to select a language and set up channels.

•To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Channels will not be set up, and CHANNELS NOT SET will appear on the screen briefly.

•You cannot set up channels if you are using a Cable Box.

•Line Input mode will always be stored in the TV/VCR’s memory as channel 00. When you select chan- nel 00, A/V IN will appear on the screen briefly. Press the CHANNEL K/L buttons or the Number but- tons to select another channel.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Tvcr Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Using the Remote ControlTV/VCR Maintenance Recording PreventionRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Hooking Up the TV/VCR cont’d Crooked Pin Straight PinYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRLanguage Selection Press the Menu buttonAutomatic Channel Setup Adding/Deleting Channels Press the PLAY/ button or the STOP/ button to selectCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’d Manual PBS Channel Selection Use the Number buttons to select your PBS station Daylight-Savings Time Time Zone Front Panel ANTenna Jack AC Power CordRear Panel Remote Control Buttons Channel / Buttons Memory ButtonALT. CH Alternate Channel Button SLEEP/WAKE UP ButtonAdjusting the Picture Controls Adjusting the Picture Controls cont’d Decrease IncreaseOn-Screen Status Displays If you select Status ON, then select Counter only OFFIf you select Status ON, then select Counter only on If you select Status OFFReminder ReminderPlaying VHS Quasi Play Back SqpbRecording To stop recording, press the STOP/ button Tape SpeedsOne-Touch Recording Press the RECord/OTR button repeatedly until the desiredRerecording Tape Duplication Different brands of equipment may operate differentlyTimer Recording DailyTimer Recording cont’d Timer Recording cont’d 1110Checking or Clearing Timer Recordings Defeat Recording REC DefeatedRepeat Play B Repeat Play Insert a tape in the TV/VCR Press the Menu buttonRepeat Play cont’d Press the STATUS/EXIT button to remove the menu. A-BReal-Time Counter Memory Playback Options Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureEnter Your Access Code SmartLockSmartLock cont’d Example Specific Sub-ratingsTo change the access code, follow these steps Rating Explanations Wake Up Timer Press the SLEEP/WAKE UP buttonSleep Timer Closed Caption ExampleMenu ScreenClosed Caption cont’d Standard Closed CaptionsBlue Background Volume Bar Automatic Operation Features Specifications Helpful Hints Helpful Hints cont’d Glossary Renewed Index MemoryPage Supplied Accessories
Top Page Image Contents