SUPER MICRO Computer 6012P-6 user manual Installing the Server into a Telco Rack

Page 24

SUPERSERVER 6012P-6 Manual

Installing the Server into a Telco Rack:

If you are installing the SuperServer 6012P-6 into a Telco type rack, follow the directions given on the previous pages for rack installation. The only difference in the installation procedure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the telco rack.

Figure 2-4. Installing the Server into a Telco Rack

2-6

Image 24

Contents Super Page Preface About This ManualManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 OverviewMainboard Features ChipsetProcessors Memory Onboard ScsiPCI Expansion Slots ATI Graphics ControllerOther Features Onboard Controllers/PortsServer Chassis Features System PowerScsi Subsystem Control PanelCooling System I/O BackplaneContacting Supermicro HeadquartersEuropean Office Asia-PacificSuperserver 6012P-6 Manual Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6012P-6 Choosing a Setup Location Rack PrecautionsServer Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DPR-6GM+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header PinsInstalling Memory Dimm Installation See FigureI/O Ports Side View of Dimm Installation into Slot Memory SupportPCI card installation Adding PCI CardsPCI slots Motherboard Layout P4DPR-6GM+Jumper Description Default Setting Connector DescriptionP4DPR-6GM+ Quick Reference Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionPower Fail LED Reset ButtonOverheat LED OH Power Button Universal Serial Bus USB0/1Extra Universal Serial Bus Headers FPUSB0/1 Serial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsFan Headers LAN1/2 Ethernet PortsWake-On-LAN Wake-On-RingKeylock Jumper Settings Explanation JumpersCmos Clear LAN1 Enable/Disable LAN2 Enable/DisableVGA Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisableWatchdog Enable/Disable Onboard Indicators Thermal Fan Enable/DisablePCI-X Bus Speed Settings Speaker Enable/DisableFloppy Connector Floppy/Hard Disk Drive and Scsi ConnectionsIDE Connectors Ultra160 Scsi ConnectorsInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012P-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012P-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterRunning Setup Main Bios SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesSystem Time System DateLegacy Diskette a Legacy Diskette BLBA Mode Control Transfer ModeUltra DMA Mode TypeAdvanced Setup Installed OSQuick Boot Mode Quiet Boot Reset Configuration DataDevice Configuration Power Loss ControlInterrupt Serial Port BMode Parallel PortLarge Disk Access Mode Enable Memory GapDMA Channel Floppy Disk ControllerECC Configuration ECC Error TypeSerr Signal Condition Advanced Processor OptionsSplit Lock Operations Hyper-threadingL3 Cache DMI Event LoggingClear All DMI Event Logs Console RedirectionCOM Port Address Baud RateSupervisor Password Is User Password IsSecurity Set Supervisor Password Set User PasswordPassword on Boot Fixed Disk Boot SectorPower Acpi ModePower Savings Standby Timeout Auto Suspend TimeoutResume on Time Resume TimeBoot +Removable DevicesCD-ROM Drive Network Boot +Hard DriveIntel UNDI, PXE-2.0 PIR Select the Processors PIRSelect the Thermal Unit Processor Info ROM Data Exit ExitLoad Setup Defaults Exit Saving ChangesExit Discarding Changes Discard ChangesAppendix a PhoenixBIOS Post Messages System Cmos checksum bad Default configuration used System timer errorReal time clock error Check date and time settingsSystem cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering SetupInvalid System Configuration Data PS/2 Mouse Boot Summary ScreenFixed Disk n Device IRQ conflictPress F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupRun the I2O Configuration Utility System Bios shadowedSuperserver 6012P-6 Manual Appendix B PhoenixBIOS Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero DoctorLinux Support Figure C-1. Supero Doctor III Health Information ScreenAppendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Power Supply DimensionsWeight Expansion Slots provided with butterfly riser card