SUPER MICRO Computer 6012P-6 ECC Configuration, ECC Error Type, Serr Signal Condition, CPU Speed

Page 80

SUPERSERVER 6012P-6 Manual

ECC Configuration

This setting lets you enable or disable ECC (Error Correction and Checking). The options are ECC and Disabled.

ECC Error Type

This setting lets you select which type of interrupt will be activated as a result of an ECC error. The options are None, NMI (Non-Maskable Interrupt), SMI (System Management Interrupt) and SCI (System Control Interrupt.

SERR Signal Condition

This setting specifies the conditions required to qualify as an ECC error. Options are None, Single Bit, Multiple Bit and Both.

!Advanced Processor Options

Access the submenu to make changes to the following settings.

CPU Speed

This is a display that indicates the speed of the installed processor.

Frequency Ratio

This setting allows you to specify the value of tthe internal frequency multiplier of the processor, which is used to determine the processor speed. Options are x8, x16, x17, x18, x19 and x20.

Fast String Operations

This setting allows you to Enable or Disable fast string operations.

Compatible FPU Code

This setting allows you to Enable or Disable the compatible FPU code.

7-10

Image 80

Contents Super Page Manual Organization PrefaceAbout This Manual System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 OverviewMainboard Features ChipsetProcessors Memory Onboard ScsiPCI Expansion Slots ATI Graphics ControllerOther Features Onboard Controllers/PortsServer Chassis Features System PowerScsi Subsystem Control PanelCooling System I/O BackplaneContacting Supermicro HeadquartersEuropean Office Asia-PacificSuperserver 6012P-6 Manual Unpacking the SuperServer 6012P-6 Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DPR-6GM+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header PinsI/O Ports Installing MemoryDimm Installation See Figure Side View of Dimm Installation into Slot Memory SupportPCI slots PCI card installationAdding PCI Cards Motherboard Layout P4DPR-6GM+P4DPR-6GM+ Quick Reference Jumper Description Default SettingConnector Description Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionOverheat LED OH Power Fail LEDReset Button Extra Universal Serial Bus Headers FPUSB0/1 Power ButtonUniversal Serial Bus USB0/1 Serial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsFan Headers LAN1/2 Ethernet PortsKeylock Wake-On-LANWake-On-Ring Cmos Clear Jumper SettingsExplanation Jumpers LAN1 Enable/Disable LAN2 Enable/DisableVGA Enable/Disable Chassis/Overheat Fan SelectWatchdog Enable/Disable Scsi Enable/DisableScsi Termination Enable/ Disable Onboard Indicators Thermal Fan Enable/DisablePCI-X Bus Speed Settings Speaker Enable/DisableFloppy Connector Floppy/Hard Disk Drive and Scsi ConnectionsIDE Connectors Ultra160 Scsi ConnectorsInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012P-6 User’s Manual Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012P-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterPress the Delete key to enter Setup Running SetupMain Bios Setup Main Bios Setup Menu Main Setup FeaturesSystem Time System DateLegacy Diskette a Legacy Diskette BLBA Mode Control Transfer ModeUltra DMA Mode TypeQuick Boot Mode Advanced SetupInstalled OS Quiet Boot Reset Configuration DataDevice Configuration Power Loss ControlInterrupt Serial Port BMode Parallel PortLarge Disk Access Mode Enable Memory GapDMA Channel Floppy Disk ControllerECC Configuration ECC Error TypeSerr Signal Condition Advanced Processor OptionsSplit Lock Operations Hyper-threadingL3 Cache DMI Event LoggingClear All DMI Event Logs Console RedirectionCOM Port Address Baud RateSecurity Supervisor Password IsUser Password Is Set Supervisor Password Set User PasswordPassword on Boot Fixed Disk Boot SectorPower Savings PowerAcpi Mode Standby Timeout Auto Suspend TimeoutResume on Time Resume TimeCD-ROM Drive Boot+Removable Devices Intel UNDI, PXE-2.0 Network Boot+Hard Drive Select the Thermal Unit PIRSelect the Processors PIR Processor Info ROM Data Exit ExitLoad Setup Defaults Exit Saving ChangesExit Discarding Changes Discard ChangesAppendix a PhoenixBIOS Post Messages System Cmos checksum bad Default configuration used System timer errorReal time clock error Check date and time settingsSystem cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering SetupInvalid System Configuration Data PS/2 Mouse Boot Summary ScreenFixed Disk n Device IRQ conflictPress F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupRun the I2O Configuration Utility System Bios shadowedSuperserver 6012P-6 Manual Appendix B PhoenixBIOS Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero DoctorLinux Support Figure C-1. Supero Doctor III Health Information ScreenAppendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Power Supply DimensionsWeight Expansion Slots provided with butterfly riser card