SUPER MICRO Computer 6012P-6 user manual Removing/Replacing the Power Supply

Page 69

Chapter 6: Advanced Chassis Setup

Figure 6-5. Removing/Replacing the Power Supply

6-9

Image 69

Contents Super Page Preface About This ManualManual Organization Advanced Motherboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Motherboard Setup System SafetyAdvanced Chassis Setup Appendices BiosPage Overview Chapter Introduction to the SuperServer 6012P-6Chipset Mainboard FeaturesOnboard Scsi Processors MemoryPCI Expansion Slots ATI Graphics ControllerOnboard Controllers/Ports Other FeaturesSystem Power Server Chassis FeaturesScsi Subsystem Control PanelI/O Backplane Cooling SystemHeadquarters Contacting SupermicroEuropean Office Asia-PacificSuperserver 6012P-6 Manual Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6012P-6 Choosing a Setup Location Rack PrecautionsServer Precautions Identifying the Sections of the Rack Rails Installing the SuperServer 6012P-6 into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Chapter Advanced Motherboard SetupHandling the P4DPR-6GM+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables P4DPR-6GM+ Front Control Panel Header Pins Connecting the Control PanelInstalling Memory Dimm Installation See FigureI/O Ports Memory Support Side View of Dimm Installation into SlotPCI card installation Adding PCI CardsPCI slots P4DPR-6GM+ Motherboard LayoutJumper Description Default Setting Connector DescriptionP4DPR-6GM+ Quick Reference ATX Power Connection Connector DefinitionsPower LED Pwrsec ConnectionPower Fail LED Reset ButtonOverheat LED OH Power Button Universal Serial Bus USB0/1Extra Universal Serial Bus Headers FPUSB0/1 ATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsFan Headers LAN1/2 Ethernet PortsWake-On-LAN Wake-On-RingKeylock Jumper Settings Explanation JumpersCmos Clear LAN2 Enable/Disable LAN1 Enable/DisableVGA Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisableWatchdog Enable/Disable Thermal Fan Enable/Disable Onboard IndicatorsPCI-X Bus Speed Settings Speaker Enable/DisableFloppy/Hard Disk Drive and Scsi Connections Floppy ConnectorUltra160 Scsi Connectors IDE ConnectorsDriver/Tool Installation Display Screen Installing Software DriversSuperserver 6012P-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front and Rear Views Control PanelSystem Fans Installing a new fanSystem Fan Failure Replacing System Cooling FansAccessing the Drive Bays Drive Bay Installation/RemovalMounting a Scsi drive in a drive carrier Scsi Drive InstallationInstalling/removing hot-swap Scsi drives SCA Backplane CD-ROM and Floppy Drive InstallationPower Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012P-6 Manual How To Change the Configuration Data System BiosStarting the Setup Utility ChapterRunning Setup Main Bios SetupPress the Delete key to enter Setup Main Setup Features Main Bios Setup MenuSystem Time System DateLegacy Diskette B Legacy Diskette aTransfer Mode LBA Mode ControlUltra DMA Mode TypeAdvanced Setup Installed OSQuick Boot Mode Reset Configuration Data Quiet BootDevice Configuration Power Loss ControlSerial Port B InterruptMode Parallel PortEnable Memory Gap Large Disk Access ModeDMA Channel Floppy Disk ControllerECC Error Type ECC ConfigurationSerr Signal Condition Advanced Processor OptionsHyper-threading Split Lock OperationsL3 Cache DMI Event LoggingConsole Redirection Clear All DMI Event LogsCOM Port Address Baud RateSupervisor Password Is User Password IsSecurity Set User Password Set Supervisor PasswordPassword on Boot Fixed Disk Boot SectorPower Acpi ModePower Savings Auto Suspend Timeout Standby TimeoutResume on Time Resume TimeBoot +Removable DevicesCD-ROM Drive Network Boot +Hard DriveIntel UNDI, PXE-2.0 PIR Select the Processors PIRSelect the Thermal Unit Processor Info ROM Data Exit ExitExit Saving Changes Load Setup DefaultsExit Discarding Changes Discard ChangesAppendix a PhoenixBIOS Post Messages System timer error System Cmos checksum bad Default configuration usedReal time clock error Check date and time settingsFail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering SetupPS/2 Mouse Boot Summary Screen Invalid System Configuration DataFixed Disk n Device IRQ conflictPress F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousRun the I2O Configuration Utility System Bios shadowedSuperserver 6012P-6 Manual Recoverable Post Errors Appendix B PhoenixBIOS Post CodesTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Appendix C Supero Doctor Key FeaturesFigure C-1. Supero Doctor III Health Information Screen Linux SupportAppendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Dimensions Power SupplyWeight Expansion Slots provided with butterfly riser card