SUPER MICRO Computer 6012P-6 user manual Control Panel, Chassis Front and Rear Views

Page 62

SUPERSERVER 6012P-6 Manual

Floppy Drive

Slim-Line CD-ROM Drive

System LEDs

Control Panel

SCSI Drives

NMI

System Reset Main Power

Figure 6-1. Chassis: Front and Rear Views

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the JF2 connector on the motherboard to provide you with system status indications. A ribbon cable has bundled these wires together to simplify the connection. Connect the cable from JF2 on the motherboard to the appro- priate header on the Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all excess cabling out of the airflow path.

The control panel LEDs inform you of system status. See "Chapter 3: System Interface" for details on the LEDs and the control panel buttons. Details on JF2 can be found in "Chapter 5: Advanced Motherboard Installa- tion."

6-2

Image 62

Contents Super Page Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 OverviewMainboard Features ChipsetPCI Expansion Slots Processors MemoryOnboard Scsi ATI Graphics ControllerOther Features Onboard Controllers/PortsScsi Subsystem Server Chassis FeaturesSystem Power Control PanelCooling System I/O BackplaneEuropean Office Contacting SupermicroHeadquarters Asia-PacificSuperserver 6012P-6 Manual Unpacking the SuperServer 6012P-6 Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Handling the P4DPR-6GM+ Motherboard Chapter Advanced Motherboard SetupPrecautions UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header PinsI/O Ports Installing MemoryDimm Installation See Figure Side View of Dimm Installation into Slot Memory SupportPCI slots PCI card installationAdding PCI Cards Motherboard Layout P4DPR-6GM+P4DPR-6GM+ Quick Reference Jumper Description Default SettingConnector Description Power LED Connector DefinitionsATX Power Connection Pwrsec ConnectionOverheat LED OH Power Fail LEDReset Button Extra Universal Serial Bus Headers FPUSB0/1 Power ButtonUniversal Serial Bus USB0/1 Fan Headers Serial PortsATX PS/2 Keyboard and PS/2 Mouse Ports LAN1/2 Ethernet PortsKeylock Wake-On-LANWake-On-Ring Cmos Clear Jumper SettingsExplanation Jumpers VGA Enable/Disable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectWatchdog Enable/Disable Scsi Enable/DisableScsi Termination Enable/ Disable PCI-X Bus Speed Settings Onboard IndicatorsThermal Fan Enable/Disable Speaker Enable/DisableFloppy Connector Floppy/Hard Disk Drive and Scsi ConnectionsIDE Connectors Ultra160 Scsi ConnectorsInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012P-6 User’s Manual Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear ViewsSystem Fan Failure Installing a new fanSystem Fans Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplaneRemoving/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012P-6 Manual Starting the Setup Utility System BiosHow To Change the Configuration Data ChapterPress the Delete key to enter Setup Running SetupMain Bios Setup System Time Main Bios Setup MenuMain Setup Features System DateLegacy Diskette a Legacy Diskette BUltra DMA Mode LBA Mode ControlTransfer Mode TypeQuick Boot Mode Advanced SetupInstalled OS Device Configuration Quiet BootReset Configuration Data Power Loss ControlMode InterruptSerial Port B Parallel PortDMA Channel Large Disk Access ModeEnable Memory Gap Floppy Disk ControllerSerr Signal Condition ECC ConfigurationECC Error Type Advanced Processor OptionsL3 Cache Split Lock OperationsHyper-threading DMI Event LoggingCOM Port Address Clear All DMI Event LogsConsole Redirection Baud RateSecurity Supervisor Password IsUser Password Is Password on Boot Set Supervisor PasswordSet User Password Fixed Disk Boot SectorPower Savings PowerAcpi Mode Resume on Time Standby TimeoutAuto Suspend Timeout Resume TimeCD-ROM Drive Boot+Removable Devices Intel UNDI, PXE-2.0 Network Boot+Hard Drive Select the Thermal Unit PIRSelect the Processors PIR Processor Info ROM Data Exit ExitExit Discarding Changes Load Setup DefaultsExit Saving Changes Discard ChangesAppendix a PhoenixBIOS Post Messages Real time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupFixed Disk n Invalid System Configuration DataPS/2 Mouse Boot Summary Screen Device IRQ conflictRun the I2O Configuration Utility Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedSuperserver 6012P-6 Manual Terminal Post Errors Appendix B PhoenixBIOS Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero DoctorLinux Support Figure C-1. Supero Doctor III Health Information ScreenAppendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Weight Power SupplyDimensions Expansion Slots provided with butterfly riser card