SUPER MICRO Computer 6012P-6 user manual System Cmos checksum bad Default configuration used

Page 94

SUPERSERVER 6012P-6 Manual

System CMOS checksum bad - Default configuration used

System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in CMOS. The BIOS installed Default Setup Values. If you do not want these values, enter Setup and enter your own values. If the error persists, check the system battery or contact your dealer.

System timer error

The timer test failed. Requires repair of system board.

Real time clock error

Real-Time Clock fails BIOS hardware test. May require board repair.

Check date and time settings

BIOS found date or time out of range and reset the Real-Time Clock. May require setting legal date (1991-2099).

Previous boot incomplete - Default configuration used

Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was caused by incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify that the waitstate configuration is correct. This error is cleared the next time the system is booted.

Memory Size found by POST differed from CMOS

Memory size found by POST differed from CMOS.

Diskette drive A error

Diskette drive B error

Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly.

Incorrect Drive A type - run SETUP

Type of floppy drive A: not correctly identified in Setup.

Incorrect Drive B type - run SETUP

Type of floppy drive B: not correctly identified in Setup.

A-2

Image 94
Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup Bios AppendicesPage Chapter Introduction to the SuperServer 6012P-6 OverviewMainboard Features ChipsetPCI Expansion Slots Processors MemoryOnboard Scsi ATI Graphics ControllerOther Features Onboard Controllers/PortsScsi Subsystem Server Chassis FeaturesSystem Power Control PanelCooling System I/O BackplaneEuropean Office Contacting SupermicroHeadquarters Asia-PacificSuperserver 6012P-6 Manual Preparing for Setup Chapter Server InstallationUnpacking the SuperServer 6012P-6 Rack Precautions Choosing a Setup LocationServer Precautions Installing the SuperServer 6012P-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012P-6 Manual Checking the Drive Bay Setup Superserver 6012P-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Handling the P4DPR-6GM+ Motherboard Chapter Advanced Motherboard SetupPrecautions UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel P4DPR-6GM+ Front Control Panel Header PinsDimm Installation See Figure Installing MemoryI/O Ports Side View of Dimm Installation into Slot Memory SupportAdding PCI Cards PCI card installationPCI slots Motherboard Layout P4DPR-6GM+Connector Description Jumper Description Default SettingP4DPR-6GM+ Quick Reference Power LED Connector DefinitionsATX Power Connection Pwrsec ConnectionReset Button Power Fail LEDOverheat LED OH Universal Serial Bus USB0/1 Power ButtonExtra Universal Serial Bus Headers FPUSB0/1 Fan Headers Serial PortsATX PS/2 Keyboard and PS/2 Mouse Ports LAN1/2 Ethernet PortsWake-On-Ring Wake-On-LANKeylock Explanation Jumpers Jumper SettingsCmos Clear VGA Enable/Disable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Termination Enable/ Disable Scsi Enable/DisableWatchdog Enable/Disable PCI-X Bus Speed Settings Onboard IndicatorsThermal Fan Enable/Disable Speaker Enable/DisableFloppy Connector Floppy/Hard Disk Drive and Scsi ConnectionsIDE Connectors Ultra160 Scsi ConnectorsInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012P-6 User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsSystem Fan Failure Installing a new fanSystem Fans Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysScsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplaneRemoving/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012P-6 Manual Starting the Setup Utility System BiosHow To Change the Configuration Data ChapterMain Bios Setup Running SetupPress the Delete key to enter Setup System Time Main Bios Setup MenuMain Setup Features System DateLegacy Diskette a Legacy Diskette BUltra DMA Mode LBA Mode ControlTransfer Mode TypeInstalled OS Advanced SetupQuick Boot Mode Device Configuration Quiet BootReset Configuration Data Power Loss ControlMode InterruptSerial Port B Parallel PortDMA Channel Large Disk Access ModeEnable Memory Gap Floppy Disk ControllerSerr Signal Condition ECC ConfigurationECC Error Type Advanced Processor OptionsL3 Cache Split Lock OperationsHyper-threading DMI Event LoggingCOM Port Address Clear All DMI Event LogsConsole Redirection Baud RateUser Password Is Supervisor Password IsSecurity Password on Boot Set Supervisor PasswordSet User Password Fixed Disk Boot SectorAcpi Mode PowerPower Savings Resume on Time Standby TimeoutAuto Suspend Timeout Resume Time+Removable Devices BootCD-ROM Drive +Hard Drive Network BootIntel UNDI, PXE-2.0 Select the Processors PIR PIRSelect the Thermal Unit Processor Info ROM Data Exit ExitExit Discarding Changes Load Setup DefaultsExit Saving Changes Discard ChangesAppendix a PhoenixBIOS Post Messages Real time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupFixed Disk n Invalid System Configuration DataPS/2 Mouse Boot Summary Screen Device IRQ conflictRun the I2O Configuration Utility Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedSuperserver 6012P-6 Manual Terminal Post Errors Appendix B PhoenixBIOS Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6012P-6 Manual Key Features Appendix C Supero DoctorLinux Support Figure C-1. Supero Doctor III Health Information ScreenAppendix C Supero Doctor Superserver 6012P-6 Manual Appendix D System Specifications Weight Power SupplyDimensions Expansion Slots provided with butterfly riser card