Toshiba HD-EP35KB manual Audio output, Press / to select Audio, then press OK

Page 22

Preparation (Continued)

D: Audio output

15 Press / to select “Audio”, then press OK.

SETUP MENU

Picture

 

Digital Out SPDIF

Bitstream

 

 

Audio

 

 

 

 

Digital Out HDMI

Auto

 

 

Language

 

 

 

 

Ethernet

 

Digital Direct Audio Mode

Off

 

General

 

Dynamic Range Control

Auto

 

 

 

 

 

 

 

 

Dialog Enhancement

Off

 

 

 

 

 

 

Speaker Setting

5.1ch

16 When you connected an audio system to the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack ( page 16):

Press / to select “Digital Out SPDIF”, then press OK.

Select one of the followings according to your connection, and press OK.

Bitstream

When an AV receiver or processor equipped with built-in Dolby Digital, DTS or MPEG decoder is connected to this player.

Digital Out SPDIF

Bitstream

PCM

When you play a disc recorded in Dolby Digital Plus or Dolby TrueHD format, Dolby Digital sound is output. When you play a disc recorded in DTS-HD format, the sound is converted to a DTS bitstream. If the AV receiver or processor does not support DTS, select “PCM”.

PCM

When a 2ch digital stereo amplifier is connected to this player.

When you play an HD DVD or DVD video disc recorded in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD format, sound is converted into PCM (2ch) format.

When you connected an HDMI device to the HDMI OUTPUT jack ( page 15, 16):

Press / to select “Digital Out HDMI”, then press OK.

Select one of the followings according to your connection, and press OK.

Auto

Digital Out HDMI

Auto

PCM

Downmixed PCM

When an HDMI device equipped with built-in Dolby Digital, DTS, MPEG or linear PCM decoder is connected to this player.

When you play a disc recorded in Dolby Digital Plus, Dolby TrueHD or DTS-HD, PCM is output (core only for DTS-HD).

When you play a disc recorded in Dolby Digital or DTS format, digital audio signal (bitstream audio) is output. If a connected HDMI device does not support Dolby Digital, DTS or MPEG, sound is converted into linear PCM to output.

To output high bitrate audio, select “Auto”, then make another setting. For details, see page 34.

PCM

When an HDMI device which has multi channel input is connected to this player.

When you play an HD DVD or DVD video disc recorded in multi channel in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD format, the sound is decoded and output in multi channel in linear PCM format.

Downmixed PCM

When a 2ch digital stereo AV receiver or processor is connected to this player.

When you play a DVD video disc recorded in Dolby Digital, DTS, MPEG1 or MPEG2 format, sound is converted into PCM (2ch) format to output.

Note

•Setting “Auto” or “PCM” will reduce output level of multi channel sound from the ANALOG AUDIO OUTPUT jacks and the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack if you:

–view the playback picture on an HDMI TV connected to this player.

–play an HD DVD video disc of a certain type, recorded in linear PCM format.

In this case, the output level will be restored by setting to “Downmixed PCM”.

22

HD-EP35KE_Eng.indd 22

07.8.30 7:34:44 PM

Page 21 Page 23
Image 22
Page 21 Page 23
Contents HD-EP35KB HD-EP35KE This HD DVD player employs a Laser System Result in hazardous radiation exposureLocation of the required label Following information is only for EU-member statesImportant Safety Instructions Precautions Do not use the unit when moisture condensation may occur Moisture condensation occurs during the following casesTable of contents Disc compatibility FeaturesDisc Specification Certain system requirements Important notes about HD DVDHD output jacks Customer supportFront panel Index to parts and controlsRear panel Remote control DisplaySupplied accessories AccessoriesRemote control Loading batteriesRelease TV CODE. The brand code is memorized To program the remote control to operate your TVTV control While holding down, enter a codePreparation Resolution and connectionsWhy Hdmi connection is most recommended? Proceed the following steps to set the player readyVia component video input Connecting to a TVVia Hdmi input Via Video yellow inputVia optical digital audio output Connecting to audio systemVia Hdmi output Via 5.1ch analog audio outputLAN connection Via analog audio outputInput which the player is connected to Power connectionPowering on Press ON/STANDBYPress / to select Language, then press OK Setting up the playerLanguage Press / to select On Screen Language, then press OKTime Press To select Picture, then press OK ResolutionPress To select Resolution Setting, then press OK Table below, then press OKAudio output Press / to select Audio, then press OKFront Left / Front Right When a 2ch stereo system is connected to this playerCrossover Setting Center / L Surround / R SurroundRequires proxy setting To adjust the player’s clock via the network time protocolEnter the proxy server address when your provider EthernetCookie Setting Network SpeedPlaying a disc PlayingPlayback starts If playback does not start, press Play To resume playback from the location last stopped To pause playbackTo stop playback To change playback speedTo select the camera angle To select subtitlesTo select the sound During playback, press SubtitleTo check the current status To locate a positionTo play repeatedly C/D buttons Requirements for HD DVD discs/Web-enabled network contentHD DVD playing options in the future Cursor controlsOutput sound conversion table ADVGroup Setting Disc Details Customizing the function settingsDuring stop, press Setup To return to the previous menuSettings PictureAudio Language Language code list How to select a languageEthernet GeneralMaintenance Initialize Remote Controller SoundEnable Hdmi Update FirmwareBefore calling service personnel Symptom RemedySpecification
Top Page Image Contents