Sony RM-VZ950T 17GB, To cancel Learning, If the Commander does not seem to be working

Page 17

5Press and hold the button on the other remote control, until “OK” appears in the display.

During data transfer, “LEARN” stops flashing.

After data transfer is complete, “OK” appears in the display. Then, the Commander returns to its state in Step 3.

remote control of component

S-3 S-3

VCR OK

LEARN LEARN

during data transfer

S-3

VCR

LEARN

data transfer complete

If “NG” flashes twice, and the component name flashes again

Learning was unsuccessful. Try again from Step 4.

6Repeat Steps 4 and 5 to “teach” functions to other buttons.

7Select “EXIT,” then press the Jog dial to finish Learning.

To cancel Learning

Press SET.

Notes

•If you do not perform Learning steps within 30 seconds at any point during the process, the LEARN mode ends.

•If you do not perform Step 5 within 10 seconds after Step 4, the Commander returns to its state in Step 3.

•You cannot teach to the Jog dial and the SET button.

•If the memory of the commander is full, “OVER” flashes, and the Commander returns to its state in Step 3. Erase the already “learned” function (page 21) and start over from the beginning.

If the Commander does not seem to be working

If the “learned” button does not operate properly, “teach” once again. (For example, if the volume becomes very loud after pressing 2 + only once, noise may have interfered during the Learning procedure.)

If you set a component code after “learning” a signal

If you have programmed any signal on a button by the Learning function, that signal will work even after you set a component code.

Note on the REC z signal

You can only “teach” to one button at a time. Therefore you cannot teach a sequential button operation (for example REC z + N) to a single button on your Commander.

Continued

17GB

Image 17

Contents Remote Commander Table of Contents Appendix Reassigning new components FeaturesLCD display and Jog dial for easy monitoring and operation Customisable function displayIf you want to save the batteries Installing BatteriesWhen to replace the batteries Qj Progr Programme +/- buttons Qk Recall button Location of ControlsExample At normal mode How to use the Jog dialExample At SET mode VCRSetting by entering the code number Setting the Component CodesExample To set up a Philips’ TV at S-1/TV PresetWhen you set the code number to To cancel setup10GB This exampleBefore starting to search Setting by searching11GB AMP 12GBOperating a component Operating Your Components with the Remote Commander13GB 14GB When you use a double cassette deckOperating Your Components with the Remote Commander Controlling the volume Operating Non-Preset ComponentsProgramming a component signal To control the volume of a visual component SAT, VCR, DVD16GB If another signal has already been learned by that buttonIf the Commander does not seem to be working To cancel LearningIf you set a component code after learning a signal 17GBWhen you teach the signals for the amplifier When you teach signals to +/- or buttonsInput 18GB19GB VIDEO120GB AMP AMP VIDEO1 OKTo erase the learned function of a single button 21GBChanging or erasing the function of a learned button 22GB DEL23GB DEL VCR24GB ChangingOrder Move 25GB AMPVCR Move Changing the Component Selection Order Move 26GBChanging the Name of the Component Name Example To change VCR to Sonydv Svcr27GB Changing the Name of the Component Name Exit28GB 29GB Init30GB DeleteOK? 31GB ALL Erasing all Memorized Settings DeleteALL OK? 32GBDisp Setting the time for the LCD to turn offTurning Off the LCD Disp 33GBIf NG flashes twice OFF34GB 35GB PrecautionsSpecifications 36GB Troubleshooting37GB 38GB Table of Preset FunctionsUsing Fastext SAT VCR 39GBDVD 40GBAMP 41GB42GB IndexPage Vorbereitungen InhaltGrundfunktionen Weitere FunktionenHintere Umschlagseite AnhangIndividuell einstellbare Funktionsanzeige Merkmale und FunktionenZuordnen anderer Geräte Hinweise zu Batterien Einlegen der BatterienWenn die Batterien geschont werden sollen Bedienelemente Der Jog-Dial Das LCD-DisplayBeispiel Im normalen Modus Beispiel Im Modus SETJog Dial Einstellen der GerätecodesHinweise FortsetzungSo brechen Sie die Programmierung ab 10DEDiesem Beispiel Vor dem Suchen 11DEEinstellen eines Gerätecodes mit der Suchfunktion 12DE 13DE Steuern der Geräte mit der FernbedienungSteuern eines Geräts Jog- DialDoppelkassettendecks 14DESo wählen Sie die Eingangsquelle für den Verstärker Steuern der Geräte mit der Fernbedienung Fortsetzung15DE Programmieren eines Signals Jog DialEinstellen der Lautstärke BeispielBedienen nicht vorprogrammierter Geräte 16DE17DE Hinweis zum Signal REC zSo brechen Sie die Lernfunktion ab Wenn die Fernbedienung nicht funktioniert18DE Wenn Sie die Tasten 2 +/- oder mit Signalen belegenProgrammieren der Eingangswahl am Verstärker 19DE20DE Ändern oder Löschen einer programmierten Tastenfunktion 21DE22DE 23DE Ändern der Geräteauswahlfolge Move 24DE25DE Ändern der Geräteauswahlfolge Move Fortsetzung 26DEBeispiel So ändern Sie „VCR in „SONYDV 27DEName Fortsetzung 28DE29DE 30DE Löschen aller gespeicherten Einstellungen Delete31DE Löschen aller gespeicherten Einstellungen Delete Fortsetzung 32DE33DE Ausschalten des LCD- Displays DispWenn „NG zweimal blinkt 34DEAusschalten des LCD-Displays Disp Fortsetzung 35DE Technische Daten36DE Störungsbehebung37DE SymptomAbhilfemaßnahmen38DE Tabelle derTV Fernsehgerät TOPTextSAT Satelliten-Tuner VCR Videorecorder 39DETabelle der vorprogrammierten Funktionen Fortsetzung 40DEDVD DVD-Player CD CD-Player Tape Kassettendeck 41DEMD MD-Player AMP Verstärker X, Y