Sony RM-VZ950T operating instructions Troubleshooting, 36GB

Page 36

Troubleshooting

If you have problems setting up or using the Remote Commander, first check the batteries (page 5), then check the items below.

Symptom

You cannot operate the components.

You cannot control the volume.

You cannot operate the components even after setting the component code numbers.

The Commander fails to learn the remote control signals.

Remedy

•Go closer to the component. The maximum operating distance is approximately 10 m (32.8 ft.).

•Aim the Commander directly at the component, and make sure there are no obstructions between the Commander and the component.

•Power on the components first, if necessary.

•Make sure you have selected the correct component.

•Check that the component has infrared remote capability. For example, if your component didn’t come with a remote commander, it probably isn’t capable of being controlled by a remote commander.

•The component name in the display does not correspond to the component in operation. Check the component assigned to that Setting position number and the component code.

•If your visual components are connected to an audio system, select “AMP” on your Commander to control the volume. You can also “teach” the amplifier’s singal to the 2 +/– buttons for each of your visual components on your Commander.

•If you have programmed any signal on the 2 +/– button for “TV” or “AMP” using the Learning function (page 15), that signal will not be transmitted when you control other components. To use “learned” signals, you need to program the 2 +/– buttons for each component using the Learning function.

•Set the component code correctly. If the code that is listed first for your component doesn’t work, try all the codes for your component in the order in which they are listed in the supplied “Component Code Numbers”.

•Some features may not be preset. If some or all of the buttons do not function correctly even after you have set the component codes, then use the Learning function to program the remote control signals for the component (page 15).

•The component may be operated with a code number that is not listed in the “Component Code Numbers”. See “Setting by searching” (page 11) and try setting a code number again.

•When you “teach” signals of an interactive signal exchange system remote control unit (supplied with some of Sony’s receivers and amplifiers) to the Commander, the response signal of the main unit may interfere with the learning of the Commander. In such a case, move to a place where the signals will not reach the main unit (e.g. other rooms, etc.).

36GB

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Remote Commander Table of Contents Appendix Features Reassigning new componentsLCD display and Jog dial for easy monitoring and operation Customisable function displayInstalling Batteries When to replace the batteriesIf you want to save the batteries Location of Controls Qj Progr Programme +/- buttons Qk Recall buttonHow to use the Jog dial Example At normal modeExample At SET mode VCRSetting the Component Codes Setting by entering the code numberPreset Example To set up a Philips’ TV at S-1/TVTo cancel setup When you set the code number to10GB This exampleSetting by searching 11GBBefore starting to search 12GB AMPOperating Your Components with the Remote Commander 13GBOperating a component When you use a double cassette deck Operating Your Components with the Remote Commander14GB Operating Non-Preset Components Controlling the volumeProgramming a component signal To control the volume of a visual component SAT, VCR, DVDIf another signal has already been learned by that button 16GBTo cancel Learning If the Commander does not seem to be workingIf you set a component code after learning a signal 17GBWhen you teach signals to +/- or buttons When you teach the signals for the amplifierInput 18GBVIDEO1 19GBAMP AMP VIDEO1 OK 20GB21GB Changing or erasing the function of a learned buttonTo erase the learned function of a single button DEL 22GBDEL VCR 23GBChanging Order Move24GB AMP VCR Move25GB 26GB Changing the Name of the Component NameChanging the Component Selection Order Move Svcr 27GBExample To change VCR to Sonydv Exit 28GBChanging the Name of the Component Name Init 29GBDelete OK?30GB 31GB Erasing all Memorized Settings Delete ALLALL OK? 32GBSetting the time for the LCD to turn off DispTurning Off the LCD Disp 33GBOFF 34GBIf NG flashes twice Precautions Specifications35GB Troubleshooting 36GB37GB Table of Preset Functions Using Fastext38GB 39GB SAT VCR40GB DVD41GB AMPIndex 42GBPage Inhalt VorbereitungenGrundfunktionen Weitere FunktionenAnhang Hintere UmschlagseiteMerkmale und Funktionen Zuordnen anderer GeräteIndividuell einstellbare Funktionsanzeige Einlegen der Batterien Wenn die Batterien geschont werden sollenHinweise zu Batterien Bedienelemente Das LCD-Display Der Jog-DialBeispiel Im normalen Modus Beispiel Im Modus SETEinstellen der Gerätecodes Jog DialFortsetzung Hinweise10DE Diesem BeispielSo brechen Sie die Programmierung ab 11DE Einstellen eines Gerätecodes mit der SuchfunktionVor dem Suchen 12DE Steuern der Geräte mit der Fernbedienung 13DESteuern eines Geräts Jog- Dial14DE DoppelkassettendecksSo wählen Sie die Eingangsquelle für den Verstärker Steuern der Geräte mit der Fernbedienung FortsetzungProgrammieren eines Signals Jog Dial 15DEEinstellen der Lautstärke Beispiel16DE Bedienen nicht vorprogrammierter GeräteHinweis zum Signal REC z 17DESo brechen Sie die Lernfunktion ab Wenn die Fernbedienung nicht funktioniertWenn Sie die Tasten 2 +/- oder mit Signalen belegen 18DE19DE Programmieren der Eingangswahl am Verstärker20DE 21DE Ändern oder Löschen einer programmierten Tastenfunktion22DE 23DE 24DE Ändern der Geräteauswahlfolge Move25DE 26DE Ändern der Geräteauswahlfolge Move Fortsetzung27DE Beispiel So ändern Sie „VCR in „SONYDV28DE Name Fortsetzung29DE Löschen aller gespeicherten Einstellungen Delete 30DE31DE 32DE Löschen aller gespeicherten Einstellungen Delete FortsetzungAusschalten des LCD- Displays Disp 33DE34DE Ausschalten des LCD-Displays Disp FortsetzungWenn „NG zweimal blinkt Technische Daten 35DEStörungsbehebung 36DESymptomAbhilfemaßnahmen 37DETabelle der 38DETV Fernsehgerät TOPText39DE SAT Satelliten-Tuner VCR Videorecorder40DE DVD DVD-Player CD CD-PlayerTabelle der vorprogrammierten Funktionen Fortsetzung 41DE MD MD-Player AMP VerstärkerTape Kassettendeck X, Y
Top Page Image Contents