Toshiba MW24FN3/R, MW20FN3/R Important Safeguards / Power Source, To USE AC Power Source

Page 5

IMPORTANT SAFEGUARDS / Power Source

27.NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

Introduction

 

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC SERVICE

GROUNDING CONDUCTORS

EQUIPMENT

(NEC SECTION 810-21)

 

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

NEC-NATIONAL ELECTRICAL CODE

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

 

IMPORTANT RECYCLING INFORMATION

This product uses both Cathode RayTube (CRT) and other components that contain lead. In your community there might be regulations that require you to dispose these materials properly under environmental considerations. Please contact your local authorities, or the Electronic Industries Alliance (http://www.eiae.org) for disposal or recycling information.

Power source

AC Outlet

Wider Hole

and Blade

Polarized AC Cord Plug

(One blade is wider than the other.)

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

• Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.

• If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet.

• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.

• If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing the power button on the front panel.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents MW20FN3/R MW24FN3/R Location of the required Marking IntroductionAccessories CleaningPower Sources Grounding or Polarization POWER-CORD ProtectionReplacement Parts Power LinesSafety Check Connecting Laser BeamTo USE AC Power Source Important Safeguards / Power SourceDo not use the unit when moisture condensation may occur PrecautionsTo obtain a clear picture Moisture condensation occurs during the following casesOn storing discs On handling discs Structure of disc contentsOn cleaning discs DVD On Video CDsPlayable discs Contents Rear panel Identification of ControlsFront panel DVD TV/VCR operation statusDVD/Audio CD/Video CD operation status Volume Remote controlClosed Caption button ChannelOperation Battery precautionsConnections Antenna connectionsFor subscriber to scrambled cable TV service For subscriber to basic cable TV serviceCable TV Connections ConnectionsConnecting to an audio system Connecting to optional equipmentConnecting a camcorder or a TV game Dolby Digital Connecting to an amplifier equipped with a DTS decoderUse DVD video discs encoded via the MPEG2 recording system Basic setup Setting the languageSetting the language Auto Clock setting Clock settingAuto Clock adjustment To set Auto Clock to OFFTo set daylight saving time To set standard timeEnter Manual clock settingTo make corrections any time during the process TV Operation VolumeTV operation TV/VCRChannel return Sleep MuteChannel Closed Captions What is Closed CAPTIONING?Closed Captioning with a VCR To View Closed CaptionsTV/CATV selection Tuner settingSetting channels automatically To ADD/DELETE channels Select the desired channel to be added or deleted using orPress or to select ADD/DELETE, then press Enter Press Enter to select ADD or DELTo set the V-chip Setting the V-ChipTo register password PG-13 Parental guidance Press or to select desired rating, then press EnterPress To select V-CHIP Press Enter to display ON. V-CHIP SETPress MENU. Press or to select TV SETUP, then press Enter To Change passwordEnter the same password again to confirm, then press Enter Press or to select Change PASSWORD, then press EnterTo set the on timer To set the on timerPress or to select ON/OFF TIMER, then press Enter Press or to select on TIMER, then press EnterTo set the off timer To set the off timerPicture control adjustment Picture control adjustmentSound control adjustment Sound control adjustmentPress To adjust the setting Press or to select AUDIO, then pressLoading Loading and unloading a cassette tapeUnloading To prevent accidental erasureRewind or forward the tape Cassette tape playbackPlayback Special playback Repeat playback Using the real time tape counterConvenient function VCR Zero return function Video head cleaningRecording VCR Recording a TV programRecording a TV program PAUSE/STILL To stop recordingTo stop recording temporarily One-touch Timer Recording OTR One-touch Timer Recording OTRTo cancel OTR Set TV or Catv option to the appropriate positionExample Timer recordingTimer recording If the programs overlap another To set daily/weekly timer To confirm the settingsTo cancel a program Setting the surround sound Setting the stable sound Setting the surround sound Setting the stable soundOther functions VCR To cancel the surround sound mode Other functions VCRPress or to select SAP. Then press Enter to select on Second Audio Program SAP Stereo recording and playbackListening to SAP Output selectionDuplicating a video tape Duplicating a video tapeDuplicating a DVD or CD disc Recording a DVD/CD discPress DVD to select DVD mode PowerPreparation VCD PreparationVCD Playback procedure Playback procedureVCD Frame advance VCD Fast forward playbackReview playback VCD Slow-motion playbackDvdvcd Zooming Zooming/Locating desired sceneVCD Locating desired scene Advanced playback DVDVCD Repeat, Random and Program playback Repeat, Random and Program playback/Repeat A-BVCD Repeat A-B Program menuDVD Changing soundtrack language Changing soundtrack language SubtitlesDVD Subtitles Audio SelectDVD Changing Angles Changing angles/Title selection/DVD menuDVD Title Selection DVD DVD MenuFunction setup DVD Setting languageDVD Setting Language Return DVD Setting on screen displayPress Or Enter to select DRC Dynamic Range ControlDVD Dynamic Range Control DVD Menu Parental control settingDVD Parental control setting DVD To change the parental level To change the parental levelSetup DVD Playback will commence if the entered password was correctDVD Temporary disabling of rating level by DVD disc Load a DVD disc and press Play seeSymptoms and correction Before calling service personnelSymptoms Cause Possible Solutions Power OthersRemote Control Symptoms Cause Possible Solutions VCRIgnition Reception disturbancesLanguage code list General / input / output / supplied accessories SpecificationsSupplied accessories GeneralOthers Limited warrantyContinental United States contact Hawaii Contact How to Obtain Warranty Service
Top Page Image Contents