Toshiba MW27FPX, MW24FPX owner manual Timer recording, TV/VCR Timer REC Menu Enter

Recording (VCR)

Timer recording

Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month.

Timer recording

TV/VCR

TIMER REC

MENU

ENTER

// /

Preparation:

•Press TV/VCR to select the TV/VCR mode.

•Load a cassette tape with the erase prevention tab intact.

•Check the time and date are correct 21 .

Example:

Program a timer recording for 23rd day, channel 125 (Cable TV), 7:00 - 9:30 PM (Tape speed : SLP).

1 Press MENU, then press or to select option.

	TIMER REC SET
	AUTO REPEAT	OFF
	ENTER
	/ / / / MENU
Press or to select “TIMER REC SET”, then
2 press .	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿	￿￿￿

ENTER ￿￿￿￿￿￿￿

Set the start time, end time, channel and tape
5 speed as in step 4.	￿￿		￿￿￿
Then press ENTER.			￿￿￿￿￿￿￿
ENTER		￿￿￿￿￿￿		￿￿￿￿￿￿￿
	￿		￿￿	￿￿￿￿￿￿￿￿￿￿￿￿
Notes:	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
• Press to move cursor backward
for correction.	￿		￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
the channel to “L1” or “L2”.
• To record from external source set

6 To set the timer for another program, repeat steps 3 to 5 to set another program.

Press both TIMER REC at the same time. The

7 TIMER REC indicator will light. The Timer is programed, when the programed time is reached, the recording is automatically started.

TIMER

TIMER REC To cancel timer recording, press

3 Press or to select one of the program line, then press ENTER.

ENTER

4	Press	or	￿￿ ￿￿￿￿￿￿	￿￿
			to select the date, then press .
			￿￿￿	￿￿
	ENTER		￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

RECboth the buttons again and TIMER REC indicator will go out.

Notes:

•The VCR section cannot be used while the TIMER REC in- dicator is lit. If you want to use the VCR operation,press both TIMER REC buttons at the same time to deactivate the timer.

•When the clock is not set, you cannot select “TIMER REC”. In this case, set the clock (see pages 19~21).

•After a power failure or disconnection of the power plug,all programmed recording setting and time display will be lost upon resumption of power. In this case, reset the clock (see pages 19~21) and reprogram any timer recordings.

•If you want to correct the digits while setting, press or

until the item you want to correct, then press or to correct the desired setting.

•If programming is performed without a tape in the unit, or with a tape without an erase prevention tab, the Timer Re- cording is not possible. If a tape without an erase prevention tab is in the unit, the tape will be ejected.

40

5Q10501A [E]p38-41 40 4/17/04, 11:58 AM