To control a cable TV | CABLE |
converter: | Power |
|
POWER | TV | VCR CABLE |
| ||
|
| DVD |
Program the remote control to recognize the brand of your converter (see “Programming the remote control for use with a VCR, DVD player, or cable TV converter” below). The buttons shown at right will control the cable TV converter. Press the CABLE button first.
Channel
Numbers
Channel +/–
CH Enter
1 |
| 2 | 3 |
|
|
|
|
|
|
| +10 |
4 |
| 5 | 6 |
| 100 |
7 |
| 8 | 9 |
| 0 |
|
| CH + |
|
| |
VOL |
| MENU/ |
| VOL | |
– |
|
| + | ||
| ENTER |
| |||
|
|
|
| ||
|
| CH – |
|
| |
EXIT |
| RECALL | TV/VIDEO | FAV | |
VOL | CH RTN |
| FAV | ||
RESET | CAP/TEXT | 1/2 |
|
| |
DISPLAY | DVD CLEAR | TOP MENU | DVD MENU | ||
CODE |
| MTS | SLEEP |
| MUTE |
REW |
| PLAY |
| FF | |
TV/VCR | STOP | PAUSE/STILL | |||
REC |
|
| VCR CH | ||
|
|
| DVD SKIP |
Using the Remote Control
Programming the remote control for use with a VCR, DVD player, or cable TV converter
This remote control is
1.While holding down the CODE button, press the button for the device you want to control (VCR, DVD, or CABLE).
2.Enter the
3.Point the remote control at the VCR, DVD player, or converter and press POWER to test the code.
If the VCR, DVD player, or converter turns on, you have entered the right code.
If the VCR, DVD player, or converter does not respond to the remote control, you may have entered the wrong code. Repeat steps
For future reference, write down the codes you used:
VCR code ________________________
DVD player code ___________________
Cable TV converter code _____________
12
POWER |
|
| VCR | |
TV | VCR | CABLE | ||
| ||||
|
|
| CABLE | |
|
|
| DVD | |
1 | 2 | 3 | DVD | |
|
|
| +10 | |
4 | 5 | 6 | 100 | |
7 | 8 | 9 | 0 | |
| CH + |
| ||
VOL | MENU/ | VOL | ||
– | + | |||
ENTER | ||||
|
| |||
| CH – |
| ||
EXIT | RECALL | TV/VIDEO | FAV | |
VOL | CH RTN | FAV | ||
RESET | CAP/TEXT | 1/2 |
| |
DISPLAY | DVD CLEAR | TOP MENU | DVD MENU | |
CODE | MTS | SLEEP | MUTE | |
REW | PLAY | Code | ||
FF |
Notes:
•When shipped from the factory, the remote control is set to operate your TV.
•If you do not enter the code within 10 seconds from step 1 or if you enter a code not listed below, this operation is canceled.
•Each time you replace the batteries, you must reprogram the remote control.
•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does not respond to any of the codes for your VCR, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.
3N51001A[E] | 12 | 23/1/04, 4:22 PM |