Toshiba 17WLT46B Personal Preferences PP, Sound Indicator, Picture Mode, Sleep Timer Indicator

Page 52

Personal Preferences (PP)

All the preset values will be restored, when pressing "PP" key.

After the setting time of sleep timer has passed then TV goes automatically to stand-by. ￿￿￿￿

Sound Indicator

The alternatives of the indicator are Mono, Stereo, Dual I and ual II. This indicator is displayed under the programme num- ber indicator on the screen. "I-II" key is used to select Mono or Stereo, or Dual I or Dual II.

In Mono broadcast or in forced-mono (for stereo broadcast)6WHUHR.

In Stereo broadcast'XDO. ￿￿￿,,

If dual broadcast detected. Dual I is se- lected in default and also can be select- ed after Dual II by Remote Control.

If Dual II selected ,￿￿by Remote Control.

Picture Mode

Picture mode OSD is displayed when

WIDE” key is pressed. Picture mode can be changed to Auto, 4:3, 16:9, Cine- ma, Subtitle, Zoom or Panorama by pressing “ WIDE” key.

Sleep Timer Indicator

It is displayed on the upper right of the screen when a new programme is en- tered by digit key or by pressing “P<P”, “-

P/CH“, “P/CH+“, “79/ DTV”, “” or “” key. If sleep timer is activated it is dis- played with the TV status and erased with it after 3 seconds.

Mute Indicator

It is placed in the upper middle of the screen when enabled, and it stays there until it is disabled.

To cancel mute, there is two alternative;

the first one is pressing to "" key, this volume is set to the preceding value, and the second one is increasing the volume level, thus it starts at the minimum level to increase. By decreasing the volume level in mute state, mute will not be ig- nored, only the volume level will de- crease. If mute canceled after decreas- ing the volume level, the volume will valid with the decreased level.

No-Signal Detection (TV)

If no valid signal detected, it takes 5 min- utes for the switching to the Stand-By mode unless any signal detected or no any Remote

Control command is accessed.

After a Remote Control command (if No- Signal Timer is active) the timer stops and if no signal detected again the timer is initialized to 5 minutes and starts 3 seconds later again to count down.

It is not valid in AV ￿￿￿￿mode.

No-Signal Detection (PC)

If no valid signal detected for 5 minutes system goes to Stand-By mode. To

switch on the system press “” key.

As the last status feature, system starts from TV or PC, whichever was the status before stand-by or switch-off. Note that SCART inputs have the precedence on both TV and PC.

51

50052932-1552UK (TOSHIBA UK)17 INCH TFT51-IDTV-WO WM-dilek p65

11 05 2004 15:30

Image 52
Contents Toshiba Contents Fuse Blue WiringtheplugNeutral Live Remote Control RemotecontrolControl Panel Features Panel FeaturesIt is a remote controlled colour television and PC monitor PreparationSafety Precautions Before Switching on your TV Before Switching on your TVPower connection How to connect other devicesTo switch the TV on Switching the TV On/OffTo switch the TV off Silence Mode TuningHint Everyday operation Changing ChannelsInformation Banner Channel List Electronic Program Guide Current Programme Next programme While the EPG screen is disSoundtrack Language Ing use Digital TeletextChannel, by pressing the key Subtitle Time KEY When the TV is in analog mode ifIf there is no connected VCR de Advanced operation Configuring Your TVAudio Language Favourite Mode Parental SettingsIdtv Upgrade If there is a new software, the following message appears Advanced operation Editing the Channel List Edit Name SelectDelete Advancedoperation Menu Lock Favourite Channels Programme Reminders and Timers Programme RemindersEvent Timer Hint Re-Installation First Time Installation ADD ChannelsAdvanced operation Hint Option.&RPPRQ,QWHUIDFH Common Interface MenuAdvanced operation TV Setup LanguageOperating with Remote Control Operating the TVOperating the TV Operating with the buttons on the TV setMain menu MenuSystemSound Menu Selecting Mode Setting EffectUsing or button select H.Phone/ Line Out Press key to change balance left- wardUsing or key select Equalizer Setting AVLEqualizer Setting Contrast Setting ColourSetting Brightness Setting SharpnessSetting Noise Reduction Setting Picture ModeTo Store the Settings Feature Menu Sleep TimerChild Lock Selecting Menu LanguageInstallation Menu Setting VCR Video Cassette Recorder Mode Programme Menu Name Name. To change that letter orYou can switch your TV to AV modes by Source MenuProgramme Name, pressing key moves the cursor at the end InsertOther Features PIP Picture MenuTV Status Programme Swap PPSound Indicator Picture ModeSleep Timer Indicator Mute IndicatorPCMode PIP Picture Geometry MenuPIP picture is displayed on the screen Etry menu pressing , or OK keysPIP Source Menu Pressing , or OK keysTeletext Press P/CH + buttonText screen forward one page at a time Press P/CH buttonPress TV or button. The screen will switch to TV mode While watching a TV programme with TeletextConnect the aerial cable Connect Peripheral EquipmentThen, press button to select AV-1 or AV-2 Connecting Headphones Peripheral Equipment Connections Optional Antenna Connections Peripheral Equipment ConnectionsAudio Video For Satellite Receiver Decoder PC Input Typical Display Modes Tips/Troubleshooting Guide Tips/Troubleshooting GuideOn Digital mode On TV and monitor mode Care of the Screen Colors of image on screen are abnormalRemote Control No solutionNo Image on Display Screen For TV For MonitorSpecifications SpecificationsFor adaptor 230 V AC, 50 Hz For TV 12 V DC 3 WRMS. %10 THD