Pioneer DVD PLAYER, DVJ-X1 Setting master tempo, Jog dial functions, Hyper jog mode

Page 41

Setting master tempo

This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.

During playback, press the MASTER TEMPO button.

The master tempo indicator lights and the “MT” indicator appears on the display. In this way, the music pitch will not vary even if the TEMPO control slider is used to change the tempo (speed).

Note that sound quality will deteriorate, however, due to digital processing of the audio signals.

Jog dial functions

This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.

1.Rotate during playback (pitch bend).

When the jog dial is set to VINYL mode ON, take care to operate the jog dial by rotating its outer periphery (the inclined surface); touching the top panel will cause operation of a separate function.

Playback is accelerated (FWD+) or decelerated (REV–) in an amount corresponding to the degree of jog dial rotation. In the reverse play mode, the operating directions are reversed (accelerated when rotated in the REV– direction, and decelerated when rotated in the FWD+ direction).

When the jog dial rotation is stopped, playback returns to its previ- ous speed.

2.Rotate during playback (scratch play).

See the section “Scratch Play” in Advanced Operations (P. 42).

3.Rotate during pause (frame search).

[When jog mode is in VINYL mode OFF]

The player will enter the audible pause mode (the paused image is displayed).

When the jog dial is rotated, the audible pause position changes in individual frame units, in the direction corresponding to the direc- tion of jog dial rotation.

One full revolution of the jog dial is equivalent to 1.8 seconds (135 frames) of disc advance (or reversal).

[When jog mode is in VINYL mode ON]

The player will enter the silent pause mode (the paused image is displayed).

When the jog dial is rotated, the disc is played back in the direction and at a speed proportional to the direction and speed of jog dial rotation, and the pause position changes in individual frame units.

When the hand is removed from the surface of the jog dial and rotation stops, the unit enters the silent pause mode again with paused image displayed.

One full revolution of the jog dial is equivalent to 1.8 seconds (135 frames) of disc advance (or reversal).

4.Rotate during playback or in pause mode (spin).

See the section “Spin play” in Advanced Operations (P. 42).

5.Rotate during playback, while depressing the manual search button (super-fast search).

While holding one of the manual search buttons (REV1, FWD¡) depressed, rotate the jog dial in the direction corresponding to the direction of desired search; the search will be performed at faster- than-normal speed.

6.Rotate while depressing track search button (super-fast track search).

While holding one of the track search buttons (PREVIOUS4, NEXT¢) depressed, rotate the jog dial in the direction correspond- ing to the direction of desired search (track search or chapter search); the search will be performed at a faster-than-normal speed, propor- tionate to the direction and speed of jog dial rotation.

7.Rotate while depressing title search button. (Super-fast title search) (DVD)

(Super-fast folder search) (MP3)

While holding one of the title search buttons (TITLE +, ) depressed, turn the jog dial in the direction you wish to perform the search. Super- fast title (or folder) search will be performed in the direction the jog dial is turned, and in proportion to the speed of the jog dial’s rotation.

Note:

The top surface of the jog dial is equipped with a pressure-sensitive switch. Do not rest objects on the dial, or subject it to severe im- pact or pressure. Also, do rest drinks or other liquids near the dial; if the liquid spills, it can enter the parts of the dial, causing damage.

Basic Operations

[Hyper jog mode]

With jog mode set to VINYL ON, if the HYPERJOG MODE button is pressed so that the indicator lights, the rate of change of picture and sound produced in response to rotation of the jog dial increases to 2x the rate of change produced when the hyper jog mode is OFF.

Mixing different tracks (splicing)

This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.

(Example) To splice the next track (B) to the currently playing track (A).

Connect the first player A to DJ mixer CH-1, and second player B to CH-2.

Raise trim, channel fader, and master volume to appropriate levels, and set player A for playback.

1.Set the DJ mixer’s CROSS FADER lever to the left (CH-1) side.

Track A plays.

2.Load the desired disc on player B.

3.Press the track search button (PREVIOUS4, NEXT¢) on the player B to select the desired track B.

4.Monitor CH-2 on the DJ mixer.

5.Rotate the DJ mixer’s MONITOR LEVEL dial and listen to track B on headphones.

The main speakers produce the sound of track A only.

6.Select the cue point for track B while listening on the head- phones.

1 With the player B in playback mode, press the PLAY/PAUSE (6) button near the desired track B cue point.

If the jog mode is set to VINYL mode OFF, the audible pause

mode will be enabled; if the jog mode is VINYL mode ON, the silent pause mode will be enabled.

2Rotate the player B jog dial to find the exact cue point (first beat)

of track B.

3Once track B’s cue point has been set, press the CUE button on player B.

Sound will be muted and the cue point will be set.

7.In beat with the sound of track A from the speakers, press the player B’s PLAY/PAUSE (6) button.

The speakers will produce the sound of track A.

The headphones will produce the sound of track B.

8.Move the second player B’s TEMPO control slider so that the tempo (BPM) of track A and B are aligned.

Move the player B’s TEMPO control slider so that the displayed BPM of track B matches the BPM value for track A.

When the BPM numbers match, tempo adjustment is completed.

9.Press the player B’s CUE button.

The player B will return to the previously set track B cue point.

10.While listening to the closing sounds of player A’s track A from the speakers, press the player B’s PLAY/PAUSE (6) button.

The player B begins playing track B.

11.While confirming the sound on the headphone, steadily move the DJ mixer’s cross fader lever toward the right side.

The sounds of track B will gradually mix with and replace the sounds of track A heard from the speaker.

When the DJ mixer’s cross fader lever has moved completely to the right side, the splicing has been completed.

Long mix play

As long as the BPM rates match, track A and track B will mix well, even if the cross fader lever is in the middle position.

Fader start play

Using the cross fader start function on the DJM-600, DJM-500, DJM- 300, DJM-3000, DJM-909, or DJM-707, the mixing operation can be sim- plified by eliminating step 10 (above).

Also, when the cross fader lever is returned, the players return to the status of step 9 (above), so sound can be produced repeatedly.

41

Image 41
Contents DVJ-X1 Risk of Electric Shock Do not Open Information to UserImportant Safety Instructions Before Operating Confirming AccessoriesContents JOG Dial FeaturesLimited or disabled functions when in DJ mode About DVD playback in DJ modeHandling Precautions Types of discs playable on this unit Discs Usable with This UnitDVD operating limitations Marks displayed on DVDRegarding copyright Playing MP3 filesHandling discs Disc compositionDigital Versatile Discs DVD Compact Discs CDOperation panel Names and Functions of PartsMaster Tempo button/indicator P.41 Tempo control range indicator ±6, ±10, ±16, WideTempo Reset indicator Tempo Reset button7 8 29 28 27 26 25 24 23 DisplayRear panel Jog dial displayMain monitor image Preview monitor image Guide display area Playing images from the DVJ-X1 on a television setTotal time in chapter min Utes / secondsConnections Accessory control cordControl cord connection for relay play Connection example DJM-600When set to DJ DJ mode Setting the mode select switch Mode NORMAL/DJ rear panelWhen set to Normal Normal mode Connection to stereo amplifier without DJ mixerConnection to television monitor component video Connection to television monitor composite video/S-VideoVideo mixer Connecting the power cordConnection to video mixer How to perform setup SetupUsing the Setup Navigator Select On-Screen-Display OSD LanguageSelect whether connected amplifier supports 96kHz audio Exit Setup NavigatorSelect type of television connected Setup Menu items Using the Setup Menu To return all settings to their factory defaultsDisc-dependent settings Press the Setup buttonDigital output setting Advanced settingsAdjusting Dolby Digital audio Digital output ON/OFF Expert Mode Audio2 settingsSurround setting Mpeg outputHi-Bit function Expert Mode Video1 settingsSet the screen aspect ratio for the television Aspect ratio formats With conventional television setSelect S-Video output Expert Mode Video quality adjustScreen Saver setting Expert mode To select a preset picture qualityRepeat steps 3-4 for all desired setting items Adjusting picture qualityPress the Enter button Select Video Memory Select and press the Enter buttonLanguage settings Video2 settingsSelect the Subtitle Language Automatic language and subtitle settingSet DVD menu language Expert Mode Language Code List Set Subtitle Display ON/OFF Expert ModeSet language for forced subtitles Expert Mode Recording a password Setting Parental LockTo change your password Change the Parental Lock levelTo change the country code Country Code ListPrecautions when playing 8cm CD singles Set the rear panel Power switch to onLoading and Removing Discs Forced eject functionWhen a DVD is loaded When a CD is loadedBeginning playback Example Main MenuTo stop playback To temporarily interrupt playback pause modeAuto cue function Changing the viewing angle DVD only To turn off the angle indicatorFast forward/fast reverse Super-fast searchFolder search MP3 only Track search skipTitle search DVD only Changing playback speed Setting cue pointsHyper jog mode Setting master tempoJog dial functions Mixing different tracks splicingScratch play Advanced OperationsSpin play Hot cueAbout fader start play Loop playbackReverse play Selecting tracks with MP3 navigator MP3 only Relay play with two playersPress the Menu button Press the Enter buttonRegarding Text display Wave displayTo view guide displays Use the TEXT/WAVE select button to select Wave displayRecording to memory cards Operations Using Memory CardsTo recall data recorded on memory cards Player display ContentsMessage displays during recording of cue and loop points To recall a recorded cue or loop pointTo recall a memorized hot cue point To read a cue/loop point into a hot cueTo delete individual cue/loop points To delete information recorded on memory cardsTo delete all cue/loop point information for an Entire disc To delete all memory card dataTroubleshooting ¶ 96kHz PCM Out option is set to 96kHz 3 48kHz Error code Error type Error content Cause and remedy Error message displayDot Matrix Guide Display Messages Specifications Pioneer Electronics of Canada, Inc 800 782CA 90801-1760, U.S.A Allstate Parkway Markham, on L3R OP2 905 877TSZZF/05G00000
Related manuals
Manual 103 pages 1.83 Kb