When On is selected, When Auto is selected

Adjust the output level from

the speakers (Gain setting)

This setting should be made when the AUDIO OUT (5.1 channel) jacks on the rear panel are connected to an AV amplifier or receiver. The output level of each speaker in your system can be set and confirmed. The factory setting is set to [Fix]. However, when you want to adjust the output level, select [Variable].

Audio1 Audio2 Video Language General

Audio DRC –	Off
Audio Out –	5.1 Channel
Speaker Setting
Gain Setting	Fix
Gain Setting	Fix
CD Digital Direct –	VariableOff
Move
Move		SETUP	Exit

Settings: Fix*

Variable

* Factory setting

When "Variable" is selected

1 Move the cursor control joystic up or down to select the speaker.

Speakers set to [Off] in the [Speaker Setting] setting cannot be selected.

Audio1 Audio2 Video Language General

	Gain Setting
L	—	0.0 dB			L		R
C		–2.0 dB			L		R
C		–2.0 dB
R	—	0.0 dB					SW
RS	—	0.0 dB					SW
RS	—	0.0 dB				LS RS
LS	—	0.0 dB				LS RS
SW	—	0.0 dB					Return
Move			ENTER	Select		SETUP	Exit

2 Move the cursor control joystick right or left to set the output level.

The value can be adjusted in the range of -6.0 dB to

6.0dB in 0.5 dB increments. The output level of front L/R speakers are fixed and therefore cannot be adjusted.

3 Repeat steps 1 and 2 for each speaker in your system.

Set to Test tone

You can’t use the Test Tone function when the [Audio Out] setting is [2 Channel] (page 32).

The Test Tone will not work with the disc tray open, or while a disc is playing.

4 Move the cursor control joystic up to select [Gain Setting] and press cursor control joystic right.

5 Move the cursor control joystic up or down to select the speaker.

Off: Test tone is not output. (Factory Setting)

On: Test tone output is manually controlled.

Auto: Test tone is automatically output.

Audio1 Audio2 Video Language General

	Test Tone
L	—	On			L		R
C	—	Off			L		R
C	—	Off
R	—	Off					SW
RS	—	Off					SW
RS	—	Off				LS RS
LS	—	Off				LS RS
LS	—	Off
SW	—	Off					Return
Move			ENTER	Select		SETUP	Exit

When "On" is selected

Move the cursor control joystick up to the speaker selection line, then Move the cursor control joystick right or left to select the speaker to output the test tone from. The test tone is output from the selected speaker. To output the test tone from another speaker, change the speaker selection.

When "Auto" is selected

Test tone is output in the following order. Front Left, Center, Front Right, Surround Right, Surround Left, Front Left, ...

6 Move the cursor control joystic up to select [Test Tone] and press cursor control joystic left.

This takes you back to the Gain Setting screen.

7 Move the cursor control joystick up or down to select the speaker, then move the cursor control joystick right or left to adjust the output level while listening to the test tone.

To stop the test tone

Move the cursor control joystick down to the "Test Tone" setting, then move the cursor control joystick right or left to select [Off] in the [Test Tone] setting.

Notes

•When [Variable] is selected, the output level of all speakers is uniformly set to –6.0 dB. The output level of each speaker (center, surround, or sub woofer) can then be adjusted in the range of –6.0 dB to 6.0 dB. "6.0 dB" is the maximum level of [Variable] and also the level set for [Fix]. Therefore, when [Variable] is selected, the output level will usually be lower than when the setting is set to [Fix].

•The [Variable] setting has no effect on CD and Video CD playback.

•The test tone is not output when the setting is set to [2 Channel] in the [Audio Output] setting (page 32), while the disc tray opens, or while a disc is playing.