JBL 260 user manual Getting Started Rear Panel Connections

Page 10

Section 1

 

 

 

 

DriveRack

 

 

 

®

 

 

Getting Started

 

 

1.1 Rear Panel Connections

IEC Power Cord Receptacle

The DriveRack 260 comes with a power supply that will accept voltages ranging from 100V-120V at frequencies from 50Hz-60Hz (domestic version model). An IEC cord is included. The EU version accepts 220V-240V at frequencies from 50Hz-60Hz.

Power Switch

The Power Switch turns the DriveRack 260 on and off. Note: dbx Professional Products recommends that power amplifiers connected to the DriveRack 260, should be powered down prior to cycling the power on the DriveRack 260.

PC Connection

This DB-9 type connection is used to send and receive information to and from the GUI interface and for firmware updates.

RS485 Zone Control Input (RJ-45 connector type)

This input connection is used to send information and power to the ZC wall controllers.

Outputs 1-6

The output section of the DriveRack 260 offers six electronically balanced XLR connectors.

Inputs 1-2

The input section of the DriveRack 260 offers two electronically balanced XLR connectors.

Ground Lift Switch

The ground lift switch lifts the pin 1 chassis ground of both input XLR connectors.

RTA Input Jack

This balanced XLR input is used for the connection of an RTA microphone, which allows the user to “Pink” and optimize the EQ settings of any room through the use of the Auto EQ in the Wizard setup assistant.

2

 

DriveRack® User Manual

 

 

Image 10
Contents DriveRack Important Safety Information Electromagnetic Compatibility Table of Contents DriveRackIntro Introduction DriveRack 260 FeaturesDefining the DriveRack 260 System Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Getting Started Rear Panel Connections Getting Started Front Panel Getting Started Quick Start ConnectionsGetting Started Section DriveRack DriveRack DriveRack DriveRack DriveRack DriveRack Functions Editing Functions Basic Navigation Modes Effect Button Array OverviewEditing Functions Navigating the Pre-EQ -GEQ and PEQ Navigating the Crossover SectionEditing Functions Navigating the Other Section Navigating the Dynamics SectionEditing Functions Navigating the Delay Section Navigating the Utility/Meters SectionEditing Functions Navigating the Wizard Section Navigating the I/O SectionFunctions Navigating Factory Programs Configuration FunctionsProgram Definition Selecting ProgramsEditing Factory Programs Navigation ModesConfiguration Functions Saving Factory Program Changes Store Program ReplacingSelect Configuration Functions Creating a User ConfigurationSignal Path Link/UnlinkComp Select RouteSelect Link/Unlink Mono DLY 20 MS 810 ms Unused Select Link/UnlinkSaving Configuration Changes Route Name Output Ch2Detailed Detailed Parameters Pre-Crossover EQ 28 Band Graphic or 9-Band ParametricFeedback Eliminator Subharmonic Synthesizer Gate Detailed Parameters Automatic Gain Control AGC Crossover Detailed Parameters Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Gain G -20 to +20 dB Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Auto On/OffHold 0 to 500 m Sec per band or global Limiter On/OffAttack .01 to 200 m Sec per band or global Release 360 to 5 dB / Sec per band or globalAlignment Delay Input RoutingOutput Meters LCD Contrast / Auto EQ Plot Utility LCD Contrast Auto EQ PlotUtilities/Meters PUP Program/MuteZC Setup Panel Power Up Modes PUP Program Stored PUP Mute CurrentZC Setup Output Panel ZC-2 BoostCut Panel 1 ZC-3 Select a No ChangeSet Security Level Pre EQ Low Panel ZC-4 Switch 1 2 3 No ChangeSecurity Password Edit High Password Edit Med Password Press Store to ChangeSet 260 Device Level High Password Enter PasswordProgram List/Program Change Prog Change Mode Program List Prog Lock Program ListZone Controllers Panel INS a Comp o+LIM 0+ Output Trims NetPage Control Remote Control DriveWare PC Software GUISection Basic Operation DriveRack Remote Control ZC-Zone Controllers Zone Controller InstallationZC-1 & ZC-2 Zone Controller Wiring Section Diagram a Diagram B Diagram C Guide Hardware Application GuideMono 4-Way w/ Two Aux Zones SoftwareApplication Guide Stereo Tri-amp Application Guide Stereo w/ four Aux Zones Application Guide Stereo Bi-amp w/ Dual Delay Page DriveRackAppendix Appendix Factory Reset Power Up Quick Key OptionsAppendix Specifications Analog InputsAppendix Auto EQ Optimization Tips Adjust Crossover Output Gains gain structureLook out for Modes Appendix Crossover Diagrams Main Speakers Power Amplifiers Appendix Program List/ Speaker Tunings/ Power Amp TuningsProgram List Appendix Block Diagram DriveRackAppendix aAppendix Input and Output Diagrams System Setup and Gain Structure Appendix Gain Level JumpersAppendix

260 specifications

The JBL 260 is a powerful and versatile loudspeaker that embodies the brand's renowned commitment to audio excellence. Known for its striking design and rich sound quality, the JBL 260 caters to both audiophiles and casual listeners alike, ensuring an immersive listening experience in any environment.

One of the standout features of the JBL 260 is its high-efficiency design, which allows it to deliver exceptional sound performance even in larger spaces. The speaker is equipped with a robust 6.5-inch woofer that provides deep, resonant bass, while a 1-inch soft dome tweeter ensures clear and detailed high frequencies. This combination results in a balanced sound signature that captures the subtle nuances of various music genres.

The JBL 260 employs advanced technologies such as Harman's proprietary Polished Surface Com Acoustic Design, which minimizes cabinet vibrations and resonances. This technology contributes to the overall clarity of the audio output, allowing for a more natural soundstage. Additionally, the Waveguide technology used in the speaker enhances the dispersion of sound throughout the room, ensuring that listeners can enjoy a consistent audio quality, regardless of their position.

Connectivity is another area where the JBL 260 excels. The speaker includes versatile connection options, such as Bluetooth, allowing users to stream music wirelessly from smartphones, tablets, or computers. This makes it incredibly easy to integrate the JBL 260 into modern home entertainment systems. With a range of inputs, including RCA and auxiliary ports, the speaker can accommodate various audio sources, making it a great choice for both casual listening and serious audio setups.

The design of the JBL 260 is both sleek and functional, with a modern aesthetic that fits seamlessly into any décor. Its sturdy construction not only contributes to its durability but also enhances sound quality by minimizing unwanted distortions. The speaker is available in various finishes, allowing users to choose a model that best suits their personal style.

In summary, the JBL 260 is a feature-rich loudspeaker that brings together advanced sound technologies, versatile connectivity options, and an attractive design. It stands out as an ideal choice for anyone seeking to elevate their audio experience, making it a solid investment for years to come.