JBL 260 Editing Functions Navigating the Pre-EQ -GEQ and PEQ, Navigating the Crossover Section

Page 23

DriveRackSection 2

®

Editing Functions

2.3 Navigating the Pre-EQ Section (28-GEQ and PEQ)

To edit the parameters of the EQs used in a selected program, simply use the following procedure. From program mode, press the EQ button to reach the EQ module to be edited. Successive presses of the EQ button will move through each channel.

Navigate through the Pages of the selected EQ section by depressing "Next Page" or "Prev Page" successively until arriving at the desired Page.

EQ

The EQ button toggles through

the EQs used in

 

 

 

 

EQ

 

each channel of

 

 

 

 

 

the selected

 

 

 

 

 

 

program

 

 

 

menu.

 

 

 

 

 

 

GEQ

or

PEQ

 

GEQ On/Off

 

 

Freq- 31.5Hz-18kHz

 

 

Flatten/Restore

 

 

Gain -12dB to12dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PEQ On/Off

 

 

 

 

B1 Freq- 20Hz-20kHz

 

Flatten/Restore

 

 

 

 

Gain -12dB to12dB

 

Bell,HSelf, LShelf, LHShelf,

 

Q .20 to 16.0

GEQ/PEQ

 

B2 Freq- 20Hz-20kHz

 

 

B2 Freq- 20Hz-20kHz

...

 

Gain -12dB to12dB

 

 

Gain -12dB to12dB

 

 

 

 

 

Q .20 to 16.0

 

 

Q .20 to 16.0

 

 

 

 

 

 

 

Successive presses of the Data wheel will select effect parameters within the currently selected page.

2.4 Navigating the CROSSOVER Section

To edit the parameters of the Crossover used in a selected program, simply use the following procedure. From program mode, press the X-OVER button. Once you have reached the Crossover module, Navigate through the Pages of the selected Crossover module by pressing the "Next Page" or "Prev Page" buttons successively until arriving at the desired Page.

The XOVER button

 

XOVER

toggles through

 

 

 

 

 

 

the XOVER used in

 

 

 

each channel of

 

 

 

the selected

 

 

program

 

 

menu.

 

 

XOVER

 

Low Pass

 

 

High Pass

 

 

 

 

 

 

Freq- 19.7kHz to Out

 

 

 

Freq- 20.kHz to Out

 

 

 

Gain- -20 to 20dB

 

Repeat, for each crossover band

 

 

 

 

 

Slope-BS, BW, LR

 

 

 

Slope - BS, BW, LR

 

 

 

 

 

 

(6,12,18,24,36,48)

 

 

 

(6,12,18,24,36,48)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Successive presses of the Data wheel will select effect parameters within the currently selected page.

DriveRack® User Manual

 

15

 

 

Image 23
Contents DriveRack Important Safety Information Electromagnetic Compatibility DriveRack Table of ContentsIntro Defining the DriveRack 260 System DriveRack 260 FeaturesIntroduction DriveRackIntroduction Service Contact InfoIntroductionDriveRack Warranty Section Getting Started Rear Panel Connections Getting Started Front Panel Connections Getting Started Quick StartGetting Started Section DriveRack DriveRack DriveRack DriveRack DriveRack DriveRack Functions Effect Button Array Overview Editing Functions Basic Navigation ModesNavigating the Crossover Section Editing Functions Navigating the Pre-EQ -GEQ and PEQNavigating the Dynamics Section Editing Functions Navigating the Other SectionNavigating the Utility/Meters Section Editing Functions Navigating the Delay SectionNavigating the I/O Section Editing Functions Navigating the Wizard SectionFunctions Selecting Programs Configuration FunctionsProgram Definition Navigating Factory ProgramsNavigation Modes Editing Factory ProgramsStore Program Replacing Configuration Functions Saving Factory Program ChangesLink/Unlink Configuration Functions Creating a User ConfigurationSignal Path SelectSelect Route CompMono DLY 20 MS 810 ms Unused Select Link/Unlink Select Link/UnlinkRoute Name Output Ch2 Saving Configuration ChangesDetailed Pre-Crossover EQ 28 Band Graphic or 9-Band Parametric Detailed ParametersFeedback Eliminator Subharmonic Synthesizer Gate Detailed Parameters Automatic Gain Control AGC Post-CROSSOVER PEQ Detailed Parameters Notch FiltersCrossover Compressor/Limiter Auto On/Off Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Gain G -20 to +20 dBRelease 360 to 5 dB / Sec per band or global Limiter On/OffAttack .01 to 200 m Sec per band or global Hold 0 to 500 m Sec per band or globalInput Routing Alignment DelayOutput Meters PUP Program/Mute Utility LCD Contrast Auto EQ PlotUtilities/Meters LCD Contrast / Auto EQ PlotZC Setup Power Up Modes PUP Program Stored PUP Mute CurrentZC Setup Panel Panel 1 ZC-3 Select a No Change Panel ZC-2 BoostCut OutputSecurity Panel ZC-4 Switch 1 2 3 No ChangeSet Security Level Pre EQ Low Press Store to Change Password Edit High Password Edit Med PasswordProgram List/Program Change Password Enter PasswordSet 260 Device Level High Program List Prog Change Mode Program List Prog LockOutput Trims Net INS a Comp o+LIM 0+ Zone Controllers PanelPage Control DriveWare PC Software GUI Remote ControlSection Basic Operation DriveRack Zone Controller Installation Remote Control ZC-Zone ControllersZC-1 & ZC-2 Zone Controller Wiring Section Diagram a Diagram B Diagram C Guide Software Application GuideMono 4-Way w/ Two Aux Zones HardwareApplication Guide Stereo Tri-amp Application Guide Stereo w/ four Aux Zones Application Guide Stereo Bi-amp w/ Dual Delay Page DriveRackAppendix Power Up Quick Key Options Appendix Factory ResetAnalog Inputs Appendix SpecificationsLook out for Modes Adjust Crossover Output Gains gain structureAppendix Auto EQ Optimization Tips Appendix Crossover Diagrams Program List Appendix Program List/ Speaker Tunings/ Power Amp TuningsMain Speakers Power Amplifiers DriveRackAppendix a Appendix Block DiagramAppendix Input and Output Diagrams Appendix Gain Level Jumpers System Setup and Gain StructureAppendix

260 specifications

The JBL 260 is a powerful and versatile loudspeaker that embodies the brand's renowned commitment to audio excellence. Known for its striking design and rich sound quality, the JBL 260 caters to both audiophiles and casual listeners alike, ensuring an immersive listening experience in any environment.

One of the standout features of the JBL 260 is its high-efficiency design, which allows it to deliver exceptional sound performance even in larger spaces. The speaker is equipped with a robust 6.5-inch woofer that provides deep, resonant bass, while a 1-inch soft dome tweeter ensures clear and detailed high frequencies. This combination results in a balanced sound signature that captures the subtle nuances of various music genres.

The JBL 260 employs advanced technologies such as Harman's proprietary Polished Surface Com Acoustic Design, which minimizes cabinet vibrations and resonances. This technology contributes to the overall clarity of the audio output, allowing for a more natural soundstage. Additionally, the Waveguide technology used in the speaker enhances the dispersion of sound throughout the room, ensuring that listeners can enjoy a consistent audio quality, regardless of their position.

Connectivity is another area where the JBL 260 excels. The speaker includes versatile connection options, such as Bluetooth, allowing users to stream music wirelessly from smartphones, tablets, or computers. This makes it incredibly easy to integrate the JBL 260 into modern home entertainment systems. With a range of inputs, including RCA and auxiliary ports, the speaker can accommodate various audio sources, making it a great choice for both casual listening and serious audio setups.

The design of the JBL 260 is both sleek and functional, with a modern aesthetic that fits seamlessly into any décor. Its sturdy construction not only contributes to its durability but also enhances sound quality by minimizing unwanted distortions. The speaker is available in various finishes, allowing users to choose a model that best suits their personal style.

In summary, the JBL 260 is a feature-rich loudspeaker that brings together advanced sound technologies, versatile connectivity options, and an attractive design. It stands out as an ideal choice for anyone seeking to elevate their audio experience, making it a solid investment for years to come.