JBL 260 user manual Output

Page 46

Section 4

 

 

 

 

DriveRack

 

 

 

®

 

 

Detailed Parameters

 

 

Input 1 Level -Inf to 20dB

Adjusts the input level of input 1.

Input 2 Level -Inf to 20dB

Adjusts the input level of input 2.

Master level -Inf to 20dB

This parameter is used to control the overall level of the mixed input signals.

Pink Noise On/Off

Turns the pink noise generator on and off.

Noise Level -20 to 20

Adjusts the overall level of the pink noise generator.

4.12 Output

The output section of the DriveRack 260 provides the user with the ability to control output levels of the unit and adjust phase compensation of loudspeakers within the signal path. The output level control is located in the signal path before the limiters; this means that the limiter directly affects the output level. The parameters for the Phase/Polarity Compensation effect are as follows and are user adjustable. Please refer to section A.7 of the Appendix for a complete output signal routing diagram.

Shift On/Off

This parameter is used to turn the selected output phase parameters on or off. When Shift is off, phase is 00 and polarity is positive (+).

Polarity +/-

This parameter is used to reverse the polarity of the output signal.

Phase 0 to -175 Degrees

This parameter is variable in 5 degree increments and sets the amount of phase shift within the selected output path. The phase is referenced to the upper frequency of the selected output crossover band.

38

 

DriveRack® User Manual

 

 

Page 45 Page 47
Image 46
Page 45 Page 47
Contents DriveRack Important Safety Information Electromagnetic Compatibility Table of Contents DriveRackIntro Introduction DriveRack 260 FeaturesDefining the DriveRack 260 System Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Getting Started Rear Panel Connections Getting Started Front Panel Getting Started Quick Start ConnectionsGetting Started Section DriveRack DriveRack DriveRack DriveRack DriveRack DriveRack Functions Editing Functions Basic Navigation Modes Effect Button Array OverviewEditing Functions Navigating the Pre-EQ -GEQ and PEQ Navigating the Crossover SectionEditing Functions Navigating the Other Section Navigating the Dynamics SectionEditing Functions Navigating the Delay Section Navigating the Utility/Meters SectionEditing Functions Navigating the Wizard Section Navigating the I/O SectionFunctions Navigating Factory Programs Configuration FunctionsProgram Definition Selecting ProgramsEditing Factory Programs Navigation ModesConfiguration Functions Saving Factory Program Changes Store Program ReplacingSelect Configuration Functions Creating a User ConfigurationSignal Path Link/UnlinkComp Select RouteSelect Link/Unlink Mono DLY 20 MS 810 ms Unused Select Link/UnlinkSaving Configuration Changes Route Name Output Ch2Detailed Detailed Parameters Pre-Crossover EQ 28 Band Graphic or 9-Band ParametricFeedback Eliminator Subharmonic Synthesizer Gate Detailed Parameters Automatic Gain Control AGC Crossover Detailed Parameters Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Gain G -20 to +20 dB Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Auto On/OffHold 0 to 500 m Sec per band or global Limiter On/OffAttack .01 to 200 m Sec per band or global Release 360 to 5 dB / Sec per band or globalAlignment Delay Input RoutingOutput Meters LCD Contrast / Auto EQ Plot Utility LCD Contrast Auto EQ PlotUtilities/Meters PUP Program/MuteZC Setup Panel Power Up Modes PUP Program Stored PUP Mute CurrentZC Setup Output Panel ZC-2 BoostCut Panel 1 ZC-3 Select a No ChangeSet Security Level Pre EQ Low Panel ZC-4 Switch 1 2 3 No ChangeSecurity Password Edit High Password Edit Med Password Press Store to ChangeSet 260 Device Level High Password Enter PasswordProgram List/Program Change Prog Change Mode Program List Prog Lock Program ListZone Controllers Panel INS a Comp o+LIM 0+ Output Trims NetPage Control Remote Control DriveWare PC Software GUISection Basic Operation DriveRack Remote Control ZC-Zone Controllers Zone Controller InstallationZC-1 & ZC-2 Zone Controller Wiring Section Diagram a Diagram B Diagram C Guide Hardware Application GuideMono 4-Way w/ Two Aux Zones SoftwareApplication Guide Stereo Tri-amp Application Guide Stereo w/ four Aux Zones Application Guide Stereo Bi-amp w/ Dual Delay Page DriveRackAppendix Appendix Factory Reset Power Up Quick Key OptionsAppendix Specifications Analog InputsAppendix Auto EQ Optimization Tips Adjust Crossover Output Gains gain structureLook out for Modes Appendix Crossover Diagrams Main Speakers Power Amplifiers Appendix Program List/ Speaker Tunings/ Power Amp TuningsProgram List Appendix Block Diagram DriveRackAppendix aAppendix Input and Output Diagrams System Setup and Gain Structure Appendix Gain Level JumpersAppendix

260 specifications

The JBL 260 is a powerful and versatile loudspeaker that embodies the brand's renowned commitment to audio excellence. Known for its striking design and rich sound quality, the JBL 260 caters to both audiophiles and casual listeners alike, ensuring an immersive listening experience in any environment.

One of the standout features of the JBL 260 is its high-efficiency design, which allows it to deliver exceptional sound performance even in larger spaces. The speaker is equipped with a robust 6.5-inch woofer that provides deep, resonant bass, while a 1-inch soft dome tweeter ensures clear and detailed high frequencies. This combination results in a balanced sound signature that captures the subtle nuances of various music genres.

The JBL 260 employs advanced technologies such as Harman's proprietary Polished Surface Com Acoustic Design, which minimizes cabinet vibrations and resonances. This technology contributes to the overall clarity of the audio output, allowing for a more natural soundstage. Additionally, the Waveguide technology used in the speaker enhances the dispersion of sound throughout the room, ensuring that listeners can enjoy a consistent audio quality, regardless of their position.

Connectivity is another area where the JBL 260 excels. The speaker includes versatile connection options, such as Bluetooth, allowing users to stream music wirelessly from smartphones, tablets, or computers. This makes it incredibly easy to integrate the JBL 260 into modern home entertainment systems. With a range of inputs, including RCA and auxiliary ports, the speaker can accommodate various audio sources, making it a great choice for both casual listening and serious audio setups.

The design of the JBL 260 is both sleek and functional, with a modern aesthetic that fits seamlessly into any décor. Its sturdy construction not only contributes to its durability but also enhances sound quality by minimizing unwanted distortions. The speaker is available in various finishes, allowing users to choose a model that best suits their personal style.

In summary, the JBL 260 is a feature-rich loudspeaker that brings together advanced sound technologies, versatile connectivity options, and an attractive design. It stands out as an ideal choice for anyone seeking to elevate their audio experience, making it a solid investment for years to come.
Top Page Image Contents