JBL 260 user manual Comp, Select Route

Page 32

Section 3

 

 

 

 

DriveRack

 

 

 

®

 

 

Configuration Functions

 

 

•You are now in the Pre-Crossover EQ module. The upper left-hand corner of the display indicates what EQ type is currently selected. The A and B indicators indicate which input is currently selected. Rotate the DATA wheel to select either the 9-band Parametric EQ (PEQ) or 28 band Graphic EQ (GEQ). Pressing and then rotating the DATA wheel lets you link or unlink the input EQ modules as desired. Note that the same EQ types must be selected to link. If you plan to use the Auto EQ feature, you must select a GEQ type EQ here. Use the PREV PG and NEXT PG buttons to move through A and B and then to the next module screen which will appear something like this:

COMP

Select Link/Unlink

C N A F C B

12

•You are now in the Pre-Crossover Insert module. The upper left-hand corner of the display indicates what Insert type is currently selected. The A and B indicators indicate which input is currently selected. The 1 and 2 indicators indicate which module block is currently selected (i.e. Insert 1 or Insert 2). Rotate the DATA wheel to select either Wire (no effect), AGC, Compressor, AFS, Noise Gate or Subharmonic Synthesizer. Pressing and then rotating the DATA wheel lets you link or unlink the A and B modules. Note that the same Effect types must be selected to link. Use the PREV PG and NEXT PG buttons to move through A and B, 1 and 2 and then to the next module screen which will appear something like this:

MONO DLY 1.3 10 ms Unused Select Link/Unlink

D A D B

•You are now in the Input (Pre-Crossover) Delay module. The upper left-hand corner of the display indicates how much delay time is currently allocated to this module. The A and B indicators indicate which input is currently selected. Rotate the DATA wheel to set how much delay time will be available to the selected Input Delay module. Note that the actual delay time is not set at this point; the delay time can be set once you have exited Configuration mode. Pressing and then rotating the DATA wheel lets you link or unlink the Input Delay modules as desired. Use the PREV PG and NEXT PG buttons to move through A and B, and then to the next module screen which will appear something like this:

1X1 FILTER

Select

Route

A A 2 2

BA 3 4 A A 5 6

24

 

DriveRack® User Manual

 

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents DriveRack Important Safety Information Electromagnetic Compatibility Table of Contents DriveRackIntro Defining the DriveRack 260 System DriveRack 260 FeaturesIntroduction Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Getting Started Rear Panel Connections Getting Started Front Panel Getting Started Quick Start ConnectionsGetting Started Section DriveRack DriveRack DriveRack DriveRack DriveRack DriveRack Functions Editing Functions Basic Navigation Modes Effect Button Array OverviewEditing Functions Navigating the Pre-EQ -GEQ and PEQ Navigating the Crossover SectionEditing Functions Navigating the Other Section Navigating the Dynamics SectionEditing Functions Navigating the Delay Section Navigating the Utility/Meters SectionEditing Functions Navigating the Wizard Section Navigating the I/O SectionFunctions Configuration Functions Program DefinitionNavigating Factory Programs Selecting ProgramsEditing Factory Programs Navigation ModesConfiguration Functions Saving Factory Program Changes Store Program ReplacingConfiguration Functions Creating a User Configuration Signal PathSelect Link/UnlinkComp Select RouteSelect Link/Unlink Mono DLY 20 MS 810 ms Unused Select Link/UnlinkSaving Configuration Changes Route Name Output Ch2Detailed Detailed Parameters Pre-Crossover EQ 28 Band Graphic or 9-Band ParametricFeedback Eliminator Subharmonic Synthesizer Gate Detailed Parameters Automatic Gain Control AGC Post-CROSSOVER PEQ Detailed Parameters Notch FiltersCrossover Compressor/Limiter Threshold T -40 to +20dBu Ratio R 1.0 to Inf1Gain G -20 to +20 dB Auto On/OffLimiter On/Off Attack .01 to 200 m Sec per band or globalHold 0 to 500 m Sec per band or global Release 360 to 5 dB / Sec per band or globalAlignment Delay Input RoutingOutput Meters Utility LCD Contrast Auto EQ Plot Utilities/MetersLCD Contrast / Auto EQ Plot PUP Program/MuteZC Setup Power Up Modes PUP Program Stored PUP Mute CurrentZC Setup Panel Panel ZC-2 Boost CutOutput Panel 1 ZC-3 Select a No ChangeSecurity Panel ZC-4 Switch 1 2 3 No ChangeSet Security Level Pre EQ Low Password Edit High Password Edit Med Password Press Store to ChangeProgram List/Program Change Password Enter PasswordSet 260 Device Level High Prog Change Mode Program List Prog Lock Program ListINS a Comp o+ LIM 0+Zone Controllers Panel Output Trims NetPage Control Remote Control DriveWare PC Software GUISection Basic Operation DriveRack Remote Control ZC-Zone Controllers Zone Controller InstallationZC-1 & ZC-2 Zone Controller Wiring Section Diagram a Diagram B Diagram C Guide Application Guide Mono 4-Way w/ Two Aux ZonesHardware SoftwareApplication Guide Stereo Tri-amp Application Guide Stereo w/ four Aux Zones Application Guide Stereo Bi-amp w/ Dual Delay Page DriveRackAppendix Appendix Factory Reset Power Up Quick Key OptionsAppendix Specifications Analog InputsLook out for Modes Adjust Crossover Output Gains gain structureAppendix Auto EQ Optimization Tips Appendix Crossover Diagrams Program List Appendix Program List/ Speaker Tunings/ Power Amp TuningsMain Speakers Power Amplifiers Appendix Block Diagram DriveRackAppendix aAppendix Input and Output Diagrams System Setup and Gain Structure Appendix Gain Level JumpersAppendix

260 specifications

The JBL 260 is a powerful and versatile loudspeaker that embodies the brand's renowned commitment to audio excellence. Known for its striking design and rich sound quality, the JBL 260 caters to both audiophiles and casual listeners alike, ensuring an immersive listening experience in any environment.

One of the standout features of the JBL 260 is its high-efficiency design, which allows it to deliver exceptional sound performance even in larger spaces. The speaker is equipped with a robust 6.5-inch woofer that provides deep, resonant bass, while a 1-inch soft dome tweeter ensures clear and detailed high frequencies. This combination results in a balanced sound signature that captures the subtle nuances of various music genres.

The JBL 260 employs advanced technologies such as Harman's proprietary Polished Surface Com Acoustic Design, which minimizes cabinet vibrations and resonances. This technology contributes to the overall clarity of the audio output, allowing for a more natural soundstage. Additionally, the Waveguide technology used in the speaker enhances the dispersion of sound throughout the room, ensuring that listeners can enjoy a consistent audio quality, regardless of their position.

Connectivity is another area where the JBL 260 excels. The speaker includes versatile connection options, such as Bluetooth, allowing users to stream music wirelessly from smartphones, tablets, or computers. This makes it incredibly easy to integrate the JBL 260 into modern home entertainment systems. With a range of inputs, including RCA and auxiliary ports, the speaker can accommodate various audio sources, making it a great choice for both casual listening and serious audio setups.

The design of the JBL 260 is both sleek and functional, with a modern aesthetic that fits seamlessly into any décor. Its sturdy construction not only contributes to its durability but also enhances sound quality by minimizing unwanted distortions. The speaker is available in various finishes, allowing users to choose a model that best suits their personal style.

In summary, the JBL 260 is a feature-rich loudspeaker that brings together advanced sound technologies, versatile connectivity options, and an attractive design. It stands out as an ideal choice for anyone seeking to elevate their audio experience, making it a solid investment for years to come.
Top Page Image Contents