EZQuest DVD Duplication Verify Disk or Partition? Disk, Verify Hard Disk, Burn-in Test

Page 42

Press ENT to enter the next figure. Use s t to confirm Disk or Parti.

Verify Disk or

Partition? Disk

Press ENT to verify. After verification LCD will show the results as follows.

Verify Hard Disk

OK!

5.12.6Burn-in

On the above figure press ESC and t to enter the following figure. Burn-in is to simulate the copying progress many times. The time can be from 1 to 1000. After each cycle of simulation, the DVDs on the DVD writers will eject automatically and recede for the next bout of simulation.

12-06. Adv Setup

Burn-in

Press ENT to enter the next figure. Test is simply a simulation.

Burn-in

Test

Page 42

Image 42
Contents EZQuest Duplicators Copyright and Trademark Buttons and LCD EZQuestDVD Duplicator 1-3 ver 2.03K Initialize Sdram Detect Drives Copy Copy Copying- DVD 0% 4213.4MB d2015Test TestCopy OK Erasing discTest OK Testing- DVD 0% 4213.4MB d2015Test & Copy Test & CopyVerify VerifyTest & Copy OK Verify- DVD 0% 4213.4MBCompare CompareVerify OK Compare- DVD 0% 4213.4MBSrc 02 DVD-RW Identical PrescanSrc 01 DVD-ROM Total 4213.4MB Src 02 DVD-RW TOC not matchPreScan OK Disc InfoScaning- DVD 0% 4213.4MB Disc InfoSrc DVD-ROM 01 IDE1 Master Select SourceSelect Source DVD-ROM selectedLoad ImageImage Image LoadDelete Image Image load OKImage Exists Overwrite?Yes Image P a Delete ImageImage Image Info Partition a Image is deletedImage Info Compare ImageTgt 00 HDD P a Identical Tgt 00 HDD P a TOC not matchSelect Working Partition a Select PartitionImage P a Select Partition Set Partition toSelect Img Src Edit Track for CD onlyImage Image Src Drive Load image from Drive ID-01Edit Track CD to CD Edit Edit TrackCD to CD Select Track 1/10Copying- 24X Edit 1/10 1/1 Select Track End 1Trk0325End edit disc and burn?Yes Burn CompleteSelect Track +2/10 Continue edit next Disc?YesInsert next disc Select Track End 1Trk0425Copying- 24X Edit 2/10 2/2 Continue edit next Disc?NoCD to HDD Close all discís session? YesClosing Session Please wait Edit Track CD to HDD EditLoad- P0 -24X Edit 1/10 1/1 Continue edit next Disc?Yes Load- P0 -24X Edit 2/10 2/2 Burn or Move to partition?BurnCopy- P0 -24X 0% Trk0325 Burn or Move to partition? Move Moving to P a 0%Moving to P a Play Audio Track Edit Track Play Audio TrackPlaying Track-1 0000 Close SessionEdit Track Close Session Setup SetupClosing Complete Fail Language English Setup LanguageSetup Burn Speed Burn Speed MaximumRead Speed Maximum Setup Read SpeedSetup Auto Start Drive Auto Start Drive OffStartup Menu 1.Copy Setup Startup MenuSetup Auto Verify Auto Verify OffAuto Compare Off Setup Auto CompareSetup Auto Prescan Auto Prescan OffEject Disc Setup Eject DiscSetup Burn On The Fly Eject Disc Eject Good OnlyBurn Mode Setup Burn ModeNo Valid HDD Button Sound Setup Button SoundSetup Device Info Device InfoDVD-RW DVR-103 Setup System InfoDVD-ROM DVD-116 System InfoAdv Setup UnderRun Protect Adv SetupAdv Setup UnderRun ProtectRead Error Skip Off Adv Setup OverburnAdv Setup Read Error Skip Overburn OffAll data will be lost, format? Yes Adv Setup Format HDDAdv Setup Verify HDD There is no HDDVerify Hard Disk Adv Setup Burn-inVerify Disk or Partition? Disk Burn-inSel burn-in num Run Continuous Update FirmwareAdv Setup Update Firmware Burn-in Erase&CopyAdv Setup Diagnostic Adv Setup Compare Firmware12.9 H/W Diagnostic Searching F/WLoad Default Config? Yes Load DefaultAdv Setup Load Default ≠ ↓ Enter ESC Holde ESC to exitAdv Setup CD+G 12.11 CD+GIsrc About Error Messages About LCDAbout DVD-ROM/DVD Writers About DVD Writer Not Readable About Firmware UpdateAbout Buttons About High Failure RateAbout Function 12 and Cancellation Appendix 1 List of Functions Adv Setup Appendix LCD Messages Normal ConditionsConnecting with a HDD Verify Disk or Partition?Firmware Update Audio EditingFirmware is updated successfully