EZQuest DVD Duplication user manual About LCD, About Error Messages, About DVD-ROM/DVD Writers

Page 47

Troubleshooting

6.1 About LCD

After powering on if there is no LCD, please check if the connection of power cord is frim and the environment of power outlet is normal.

6.2 About Error Messages

During Copy, Test, Compare and Verify, etc. if you press ESC to abort, an error message will appear on LCD. Abortion may cause the copy smart plus to hang up, therefore you have to power on again.

If reading fails, an error message will appear on LCD. Please get a new source DVD to try again.

If the copy smart plus hasnít detected any device after powering on, an error message will appear on LCD.

6.3 About DVD-ROM/DVD Writers

If a DVD-ROM or DVD writers cannot read, please confirm the format of the source DVD and check if it is damaged.

Use any DVD writer to read the source DVD. If it works, the DVD-ROM is probably defective or not compatible with the source DVD.

Use a fine DVD writer as the data reader, and set the ìRead Speedî at minimum.

Page 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents
EZQuest Duplicators Copyright and Trademark DVD Duplicator 1-3 ver 2.03K Initialize Sdram Buttons and LCDEZQuest Detect Drives Copy Copying- DVD 0% 4213.4MB d2015 CopyErasing disc TestCopy OK TestTest & Copy Testing- DVD 0% 4213.4MB d2015Test & Copy Test OKVerify- DVD 0% 4213.4MB VerifyTest & Copy OK VerifyCompare- DVD 0% 4213.4MB CompareVerify OK CompareSrc 02 DVD-RW TOC not match PrescanSrc 01 DVD-ROM Total 4213.4MB Src 02 DVD-RW IdenticalDisc Info Disc InfoScaning- DVD 0% 4213.4MB PreScan OKDVD-ROM selected Select SourceSelect Source Src DVD-ROM 01 IDE1 MasterImage Load ImageImage LoadImage P a Delete Image Image load OKImage Exists Overwrite?Yes Delete ImageCompare Image Partition a Image is deletedImage Info Image Image InfoTgt 00 HDD P a TOC not match Tgt 00 HDD P a IdenticalSet Partition to Select PartitionImage P a Select Partition Select Working Partition aLoad image from Drive ID-01 Edit Track for CD onlyImage Image Src Drive Select Img SrcSelect Track 1/10 Edit TrackCD to CD Edit Track CD to CD EditBurn Complete Select Track End 1Trk0325End edit disc and burn?Yes Copying- 24X Edit 1/10 1/1Select Track End 1Trk0425 Continue edit next Disc?YesInsert next disc Select Track +2/10Continue edit next Disc?No Copying- 24X Edit 2/10 2/2Edit Track CD to HDD Edit Close all discís session? YesClosing Session Please wait CD to HDDLoad- P0 -24X Edit 1/10 1/1 Continue edit next Disc?Yes Copy- P0 -24X 0% Trk0325 Load- P0 -24X Edit 2/10 2/2Burn or Move to partition?Burn Moving to P a Burn or Move to partition? MoveMoving to P a 0% Edit Track Play Audio Track Play Audio TrackEdit Track Close Session Playing Track-1 0000Close Session Closing Complete Fail SetupSetup Burn Speed Maximum Setup LanguageSetup Burn Speed Language EnglishAuto Start Drive Off Setup Read SpeedSetup Auto Start Drive Read Speed MaximumAuto Verify Off Setup Startup MenuSetup Auto Verify Startup Menu 1.CopyAuto Prescan Off Setup Auto CompareSetup Auto Prescan Auto Compare OffEject Disc Eject Good Only Setup Eject DiscSetup Burn On The Fly Eject DiscNo Valid HDD Burn ModeSetup Burn Mode Device Info Setup Button SoundSetup Device Info Button SoundSystem Info Setup System InfoDVD-ROM DVD-116 DVD-RW DVR-103UnderRun Protect Adv SetupAdv Setup Adv Setup UnderRun ProtectOverburn Off Adv Setup OverburnAdv Setup Read Error Skip Read Error Skip OffThere is no HDD Adv Setup Format HDDAdv Setup Verify HDD All data will be lost, format? YesBurn-in Adv Setup Burn-inVerify Disk or Partition? Disk Verify Hard Disk Burn-in Erase&Copy Update Firmware Adv Setup Update Firmware Sel burn-in num Run ContinuousSearching F/W Adv Setup Compare Firmware12.9 H/W Diagnostic Adv Setup Diagnostic≠ ↓ Enter ESC Holde ESC to exit Load DefaultAdv Setup Load Default Load Default Config? YesIsrc Adv Setup CD+G12.11 CD+G About DVD-ROM/DVD Writers About Error MessagesAbout LCD About High Failure Rate About Firmware UpdateAbout Buttons About DVD Writer Not ReadableAbout Function 12 and Cancellation Appendix 1 List of Functions Adv Setup Normal Conditions Appendix LCD MessagesVerify Disk or Partition? Connecting with a HDDAudio Editing Firmware UpdateFirmware is updated successfully
Top Page Image Contents