Samsung ST-54T6, ST-62T6 manual Memorizing the Channels, Selecting the Video Signal-source

Page 25

O P E R AT I O N

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH ▲ and

CH ▼ buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press MENU to display the menu.

2

Press CH ▼ two times to highlight “SET UP.”

3

Press VOL +.

The setup sub-menu will appear. Press CH ▼ to highlight ANT/CATV.

SET UP

Channel set up

ANT / CATV ANT

Time

Convergence

Language English

Caption

V-chip

Move ± Ent.

Exit

		SET UP
Channel set up
ANT / CATV		ANT
Time
Convergence
Language		English
Caption
V-chip
Move	± Sel.	Menu

4

Repeatedly press VOL + to cycle through these choices:

ANT (antenna), STD, HRC or IRC (all cable TV).

		SET UP
Channel set up
ANT / CATV		STD
Time
Convergence
Language		English
Caption
V-chip
Move	± Sel.	Menu

Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page).

CHAPTER THREE: TV OPERATION 3.5

Image 25

Contents Owner’s Instructions Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Your New TV InstallationOperation Troubleshooting Special FeaturesChapter One List of FeaturesFamiliarizing Yourself with The TV Audio in jacks Front Panel Jacks´ Video in jack Super Video Input jackSuper Video Input Rear Panel JacksAudio Inputs PIP Remote ControlNumber buttons +100PIP Controls Remote Control ¸ VCR controlsAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Connecting Cable TVSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter Connecting a VCR Antenna or cable to your VCR and your TV Connecting an S-VHS VCRConnecting a Second VCR to Record from the TV Connecting a Camcorder Installing Batteries in the Remote Control Press Power Adjusting Basic ConvergenceTurning the TV On and Off Press VOL +Adjust Blue Convergence Adjust Red ConvergenceIf a horizontal red line is Viewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Press Menu to display the menu Selecting a Menu LanguageMemorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Press MENU, then press CH twice to highlight SET UPPress VOL + again TV will beginDirectly Accessing Channels Using the Channel ButtonsChanging Channels Adding and Erasing Channels Manual MethodPress the CH or CH button to select the correct minutes Setting the ClockPress Menu three times to exit Using Mute Adjusting the VolumePress VOL + or VOL to increase or decrease the volume Video icon will be highlighted starts blink- ing Customizing the PictureAlternate method Using Automatic Picture SettingsCustomizing the Sound Using Automatic Sound Settings Video1 Video2 Video3 Viewing a VCR or Camcorder TapePress TV/VIDEO to exit Select Video jack Audio jackSetting Up Your Remote Control to Operate Your VCR Customizing Your Remote ControlTurn off your VCR VCR Codes Setting Up Your Remote Control to Operate Your Cable BoxDVD Codes Turn off your cable boxNSC Cable Box CodesPress CH twice to highlight Time Press VOL + Setting the On/Off TimerPress CH to select On time Press CH or CH to select the appropriate minutesSetting the Sleep Timer Press VOL+ Viewing Closed CaptionsPress VOL+ to open the Caption menu Select the appropriate channel Press Menu Fine Tuning ChannelsPress CH twice to highlight LNA LNA Low Noise AmplifierChoosing a Multi-Channel Sound MTS Soundtrack Special Audio Options MTS and HeadphonesPress CH to highlight MTS Setting up Wireless Headphones with Picture-in-Picture Using Wireless HeadphonesTurn the transmitter and Wireless Headphones on Activating Picture-in-Picture Viewing Picture-in-PicturePress VOL + to select the PIP menu Press VOL + to select PIP OnSelecting a Signal Source External A/V for PIP Selecting a Signal Source Antenna or Cable for PIPSwapping the Contents of the PIP image and Main image Changing the Location Rotating the PIP Window Changing the PIP ChannelFreezing the PIP Image Changing the Size of the PIP WindowSetting Up Your Personal ID Number PIN Using the V-ChipHow to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipPress CH six times to highlight the V-chip menu Press VOL+ General audience TV-Y Young children TV-Y7 Children 7 and overParental guidance TV-14SET UP Mpaa Rating Chapter Five Identifying ProblemsUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications