Samsung ST-54T6, ST-62T6 manual Example Antenna Grounding

Page 4

Protect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, con- venience receptacles, and the point where they exit from the unit.

Unplug the TV from the wall outlet and disconnect the antenna or cable system during a light- ning storm or when left unattended and unused for long periods of time. This will prevent dam- age to the unit due to lightning and power-line surges.

Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

Do not insert anything through the openings in the unit, where they can touch dangerous volt- age points or damage parts. Never spill liquid of any kind on the TV.

Ground outdoor antennas. If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF

 

ANTENNA GROUNDING

ANTENNA

 

 

LEAD IN WIRE

GROUND CLAMP

 

 

ANTENNA

 

DISCHARGE UNIT

ELECTRIC

(NEC SECTION 810-20)

 

SERVICE

GROUNDING

EQUIPMENT

CONDUCTORS

 

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

NEC — NATIONAL ELECTRICAL CODE (NEC ART 250, PART H)

Do not attempt to service the TV yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

-when the power-supply cord or plug is damaged

-if liquid has been spilled on the unit or if objects have fallen into the unit

-if the TV has been exposed to rain or water

-if the TV does not operate normally by following the operating instructions

-if the TV has been dropped or the cabinet has been damaged

-when the TV exhibits a distinct change in performance

If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to normal.

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

Upon completion of any service or repairs to this TV, ask the service technician to perform safety checks to determine that the TV is in a safe operating condition.

2SAFETY

Image 4
Contents Owner’s Instructions Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Your New TV InstallationOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Front Panel Jacks Audio in jacks´ Video in jack Super Video Input jackSuper Video Input Rear Panel JacksAudio Inputs Remote Control PIPNumber buttons +100Remote Control ¸ VCR controls PIP ControlsConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter Connecting a VCR Connecting an S-VHS VCR Antenna or cable to your VCR and your TVConnecting a Second VCR to Record from the TV Connecting a Camcorder Installing Batteries in the Remote Control Adjusting Basic Convergence Press PowerTurning the TV On and Off Press VOL +Adjust Blue Convergence Adjust Red ConvergenceIf a horizontal red line is Viewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting a Menu Language Press Menu to display the menuSelecting the Video Signal-source Memorizing the ChannelsPress MENU, then press CH twice to highlight SET UP Storing Channels in Memory Automatic MethodPress VOL + again TV will beginUsing the Channel Buttons Directly Accessing ChannelsChanging Channels Adding and Erasing Channels Manual MethodPress the CH or CH button to select the correct minutes Setting the ClockPress Menu three times to exit Using Mute Adjusting the VolumePress VOL + or VOL to increase or decrease the volume Customizing the Picture Video icon will be highlighted starts blink- ingUsing Automatic Picture Settings Alternate methodCustomizing the Sound Using Automatic Sound Settings Viewing a VCR or Camcorder Tape Video1 Video2 Video3Press TV/VIDEO to exit Select Video jack Audio jackSetting Up Your Remote Control to Operate Your VCR Customizing Your Remote ControlTurn off your VCR Setting Up Your Remote Control to Operate Your Cable Box VCR CodesDVD Codes Turn off your cable boxCable Box Codes NSCSetting the On/Off Timer Press CH twice to highlight Time Press VOL +Press CH to select On time Press CH or CH to select the appropriate minutesSetting the Sleep Timer Press VOL+ Viewing Closed CaptionsPress VOL+ to open the Caption menu Fine Tuning Channels Select the appropriate channel Press MenuLNA Low Noise Amplifier Press CH twice to highlight LNAChoosing a Multi-Channel Sound MTS Soundtrack Special Audio Options MTS and HeadphonesPress CH to highlight MTS Setting up Wireless Headphones with Picture-in-Picture Using Wireless HeadphonesTurn the transmitter and Wireless Headphones on Viewing Picture-in-Picture Activating Picture-in-PicturePress VOL + to select the PIP menu Press VOL + to select PIP OnSelecting a Signal Source External A/V for PIP Selecting a Signal Source Antenna or Cable for PIPSwapping the Contents of the PIP image and Main image Changing the PIP Channel Changing the Location Rotating the PIP WindowFreezing the PIP Image Changing the Size of the PIP WindowUsing the V-Chip Setting Up Your Personal ID Number PINHow to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipPress CH six times to highlight the V-chip menu Press VOL+ TV-Y Young children TV-Y7 Children 7 and over General audienceParental guidance TV-14SET UP Mpaa Rating Identifying Problems Chapter FiveUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications