Samsung ST-54T6, ST-62T6 manual Storing Channels in Memory Automatic Method, Press VOL + again

Page 26

O P E R AT I O N

Storing Channels in Memory (Automatic Method)

1

First, select the correct signal source (ANT, STD, HRC, IRC). See steps 1~4 on previous page.

Press MENU, then press CH ▼ twice to highlight “SET UP.”

Press VOL + to access the SETUP sub-menu. “Channel set up” will be highlighted.

2

Press VOL + while “Channel set up” is high- lighted. A new sub-menu will appear, and “Auto program” will be highlighted.

	SET UP
Channel set up
ANT / CATV	ANT
Time
Convergence
Language	English
Caption
V-chip
Move ± Ent.	Menu

		SET UP
Auto program
Fine tune		00
LNA		Off
Move	± Ent.	Menu

3
3	Auto program
Press VOL + again.	ANT 4
The TV will begin	ANT 11
memorizing all of the	+: Stop
memorizing all of the
available channels.
4
After all the available
channels are stored, the
Auto program menu
reappears. Press Menu
three times to exit.

Note: Channel auto program does not function when the V-chip is active.

▼ The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes.

Press VOL+ at any time to interrupt the memorization process and return to the Setup menu.

3.6 CHAPTER THREE: TV OPERATION

Image 26

Contents Owner’s Instructions Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Operation InstallationYour New TV Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV ´ Video in jack Front Panel JacksAudio in jacks Super Video Input jackAudio Inputs Rear Panel JacksSuper Video Input Number buttons Remote ControlPIP +100Remote Control ¸ VCR controls PIP ControlsConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsSeparate VHF and UHF Antennas Connecting Cable TVAntennas with 75-ohm Round Leads Cable without a Cable BoxConnect this cable to a two-way splitter Connecting to a Cable Box that Descrambles All ChannelsConnecting to a Cable Box that Descrambles Some Channels Connecting a VCR Connecting an S-VHS VCR Antenna or cable to your VCR and your TVConnecting a Second VCR to Record from the TV Connecting a Camcorder Installing Batteries in the Remote Control Turning the TV On and Off Adjusting Basic ConvergencePress Power Press VOL +If a horizontal red line is Adjust Red ConvergenceAdjust Blue Convergence Viewing the Display Viewing the Menus and On-Screen DisplaysViewing the Menus Selecting a Menu Language Press Menu to display the menuSelecting the Video Signal-source Memorizing the ChannelsPress VOL + again Press MENU, then press CH twice to highlight SET UPStoring Channels in Memory Automatic Method TV will beginChanging Channels Using the Channel ButtonsDirectly Accessing Channels Adding and Erasing Channels Manual MethodPress Menu three times to exit Setting the ClockPress the CH or CH button to select the correct minutes Press VOL + or VOL to increase or decrease the volume Adjusting the VolumeUsing Mute Customizing the Picture Video icon will be highlighted starts blink- ingUsing Automatic Picture Settings Alternate methodCustomizing the Sound Using Automatic Sound Settings Press TV/VIDEO to exit Viewing a VCR or Camcorder TapeVideo1 Video2 Video3 Select Video jack Audio jackTurn off your VCR Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR DVD Codes Setting Up Your Remote Control to Operate Your Cable BoxVCR Codes Turn off your cable boxCable Box Codes NSCPress CH to select On time Setting the On/Off TimerPress CH twice to highlight Time Press VOL + Press CH or CH to select the appropriate minutesSetting the Sleep Timer Press VOL+ to open the Caption menu Viewing Closed CaptionsPress VOL+ Fine Tuning Channels Select the appropriate channel Press MenuLNA Low Noise Amplifier Press CH twice to highlight LNAPress CH to highlight MTS Special Audio Options MTS and HeadphonesChoosing a Multi-Channel Sound MTS Soundtrack Turn the transmitter and Wireless Headphones on Using Wireless HeadphonesSetting up Wireless Headphones with Picture-in-Picture Press VOL + to select the PIP menu Viewing Picture-in-PictureActivating Picture-in-Picture Press VOL + to select PIP OnSwapping the Contents of the PIP image and Main image Selecting a Signal Source Antenna or Cable for PIPSelecting a Signal Source External A/V for PIP Freezing the PIP Image Changing the PIP ChannelChanging the Location Rotating the PIP Window Changing the Size of the PIP WindowUsing the V-Chip Setting Up Your Personal ID Number PINPress CH six times to highlight the V-chip menu Press VOL+ How to Enable/Disable the V-ChipHow to Set up Restrictions Using the TV guidelines Parental guidance TV-Y Young children TV-Y7 Children 7 and overGeneral audience TV-14SET UP Mpaa Rating Identifying Problems Chapter FiveSpecifications Cleaning and Maintaining Your TVUsing Your TV in Another Country