Samsung PC490-ZC Sound Problem, Go to Menu Support Self Diagnosis Sound Test p, At maximum volume

Issues	Solutions and Explanations
Sound Problem	First of all, please perform the Sound Test to confirm that your TV audio is properly operating.
	(go to MENU - Support - Self Diagnosis - Sound Test) (p. 25)
	If the audio is OK, the sound problem may caused by the source or signal.
There is no sound or the sound is too low	• Please check the volume of the device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.
at maximum volume.
The picture is good but there is no sound.	• Set the Speaker Select option to TV Speaker in the Sound menu (p. 21).
	• If you are using an external device, make sure the audio cables are connected to the correct audio
	input jacks on the TV.
	• If you are using an external device, check the device’s audio output option (ex. you may need to
	change your cable box’s audio option to HDMI when you have a HDMI connected to your TV).
	• If you are using a DVI to HDMI cable, a separate audio cable is required.
	• If your TV has a headphone jack, make sure there is nothing plugged into it.
	• Reboot the connected device by reconnecting the device’s power cable.
The speakers are making an inappropriate	• Check cable connections. Make sure a video cable is not connected to an audio input.
noise.	• For antenna or Cable connections, check the signal strength. Low signal level may cause sound
	distortion.
	• Perform the Sound Test as explained above.
No Picture, No Video
The TV won’t turn on.	• Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
	• Make sure the wall outlet is working.
	• Try pressing the POWER button on the TV to make sure the problem is not the remote. If the TV turns
	on, refer to “Remote control does not work” below.
The TV turns off automatically.	• Ensure the Sleep Timer is set to Off in the Setup menu (p. 22).
	• If your PC is connected to the TV, check your PC power settings.
	• Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
	• When watching TV from an antenna or cable connection, the TV will turn off after 10 - 15 minutes if
	there is no signal.
There is no picture/video.	• Check cable connections (remove and reconnect all cables connected to the TV and external
	devices).
	• Set your external device’s (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections
	to the TV input. For example, if an external device’s output is HDMI, it should be connected to an
	HDMI input on the TV.
	• Make sure your connected devices are powered on.
	• Be sure to select the TV’s correct source by pressing the SOURCE button on the remote control.
	• Reboot the connected device by reconnecting the device’s power cable.
RF(Cable/Antenna) Connection
The TV is not receiving all channels.	• Make sure the coaxial cable is connected securely.
	• Please try Auto Program to add available channels to the channel list. Go to MENU - Channel -
	Auto Program then select Auto and make sure the correct Cable TV signal type is set in the menu.
	There are 3 options (STD, HRC and IRC) (p. 13).
	• Verify the Antenna is positioned correctly.
No Caption on digital channels.	• Check Caption Setup menu. Try changing Caption Mode Service1 to CC1 (p. 24).
	• Some channels may not have caption data.
The picture is distorted: macro block error,	• Compression of video contents may cause picture distortion, especially with fast moving pictures
small block, dots, pixelization.	such as sports and action movies.
	• A low signal can cause picture distortion. This is not a TV problem.
PC Connection
A “Mode Not Supported” message	• Set your PC’s output resolution so it match the resolutions supported by the TV (p. 11).
appears.
“PC” is always shown on the source list,	• This is normal; “PC” is always shown on the source list, regardless of whether a PC is connected.
even if a PC is not connected.
The video is OK but there is no audio.	• If you are using an HDMI connection, check the audio output setting on your PC.

05InformationOher

English 41