Toshiba 51H94 owner manual Viewing the digital signal meter, Viewing the system status

Chapter 6: Setting up your TV

Viewing the digital signal meter

You can view the digital signal meter for ANT 1 and ANT 2 digital TV input sources only.

To view the digital signal meter:

1.Press MENU and open the SETUP menu.

2.Highlight INSTALLATION and press ENTER. (A new set of INSTALLATION menu icons will appear on-screen, as shown in step 3 below.)

Setup

Installation
Sleep Timer
On/Off Timer
HDMI Audio Selection				Auto
Side Show Interval			2 Sec
AVHD Skip Time			15 min
Convergence
				DVD RTN
	Navigate	Select			Back	EXIT	Exit
				CH RTN

3.Open the TERRESTRIAL menu, highlight SIGNAL METER, and press ENTER.

Terrestrial

Input Configuration

Channel program

Channel Add/Delete

Signal Meter

Navigate	Select	DVD RTN	Back	EXIT	Exit
		CH RTN

4.Use the yzx • buttons to select the antenna input and digital channel whose signal you want to check.

Note: The physical digital channel number listed in the Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations.

Signal Meter

Signal Locked
	78	Peak 78
Antenna		1
Physical Digital Channel		56
Virtual Digital Channel		N/A
	OK

To close the screen and return to the TERRESTRIAL menu:

Highlight OK and press ENTER.

To return to normal viewing:

Press EXIT.

Viewing the system status

To check the system status:

1.Press MENU and open the SETUP menu.

2.Highlight INSTALLATION and press ENTER. (A new set of INSTALLATION menu icons will appear on-screen, as shown in step 3).

3.Open the SYSTEM STATUS menu, highlight SYSTEM INFORMATION, and then press ENTER.

Setup

System Status

System Infomation

Installation

Sleep Timer

On/Off Timer

DVD RTN

HDMI Audio Selection

Auto

Navigate

Select

Back

EXIT

Exit

CH RTN

Side Show Interval

2 Sec

AVHD Skip Time

15 min

Convergence

DVD RTN

Navigate

Select

Back

EXIT

Exit

CH RTN

4.Use the x • buttons to scroll through the menu bar to check the Product Information and Software Version.

System Information

Thu Mar 18,2004 3:20:18 pm

Product Information

Brand:Toshiba

Model:51H94

IEEE-1394 GUID: 0000000000FFFFFF

OK

To close the screen and return to the INSTALLATION menu: Highlight OK and press ENTER.

To return to normal viewing: Press EXIT.

Restore Factory Defaults

To restore all settings and channels to their factory default values:

1.Follow steps 1Ð3 above.

2.Use the x • buttons to scroll through the menu bar to select FACTORY DEFAULTS.

3.The screen below left appears. Enter your PIN code (or 0000 if no PIN code has been set). The screen below right appears.

To cancel the reset: Highlight NO and press ENTER.

To continue the reset process: Highlight YES and press ENTER. The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the restore.

System Information			System Information
	Factory Defaults					Factory Defaults
	This window provides the ability to reset				This window provides the ability to reset
	the TV settings.					Press YES to confirm. After the TV
				the TV settings.
	Type in your PIN now (or “0000” if no PIN					turns off, unplug it and plug it
					in your PIN now (or “0000” if no PIN
	has been set) to restore settings to their			Type!		back in to complete the reset.
				has been set) to			restore settings to their
	factory default values.						Yes	No
				factory default values
		OK					OK

52		Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.
H94(E)044-52(6b-Setup)	52	8/3/04, 5:28 PM

(E) 51/57H94