HM66_EN.book Page 21 Thursday, February 23, 2006 2:49 PM
Chapter 4: Setting up your TV
To set the Quick Restart™ feature:
1
2 Highlight Quick Restart and press c.
3 Press b or B to select either On or Off and Press T.
Setup
| Installation |
|
| Off |
| |
| Sleep Timer |
|
| On |
| |
| ColorStream HD1 Audio | No |
|
|
| |
|
|
|
| |||
| HDMI 1 Audio |
| Auto |
| ||
|
|
|
|
|
|
|
| ColorStream HD2 Audio | No |
|
|
| |
|
|
|
|
|
|
|
| HDMI 2 Audio |
| Auto |
| ||
|
|
| ||||
| Quick Restart | On |
| |||
|
|
| ||||
| Navigate ENTER Select | CH RTN Back EXIT Exit | ||||
|
|
|
|
|
|
|
Note: If Quick Restart is set to Off and you turn off the TV, it can take several seconds for the picture to appear when you turn on the TV again. See “important notice about hot lamp restart,” below.
If Quick Restart is set to On and you turn off the TV, the following will occur for a few minutes:
•The screen (lamp) lights dimly; and
•The fans continue to run.
This is a function of the Quick Restart Shutdown mode and is not a TV malfunction. If you do not prefer this, set the Quick Restart feature to Off.
When the Quick Restart feature is set to Off, if you repeatedly turn the TV on and off in a short period of time, the useful service life of the lamp may be shorter than the average useful service life (- page 47).
IMPORTANT NOTICE ABOUT “HOT LAMP RESTART”
When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear
•When the Quick Restart™ feature is set to Off and you turn the TV off and then on again within a few minutes; or
•If the TV is on when a
power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes.
This is a property of DLP™ TV lamp technology and is NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will blink (and the blue LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If both LEDs are blinking, you will need to turn the TV off and then on again to restart the lamp.
Viewing the digital signal meter
You can view the digital signal meter in the ANT 1 and ANT 2 digital TV input sources only.
To view the digital signal meter:
1 Press Yand open the Setup menu.
2 Highlight Installation and press T.
3 A new set of Installation menu icons will appear on- screen, as shown below.
Open the Terrestrial menu, highlight Signal Meter, and press T.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate ENTER Select CH RTN Back EXIT Exit
4 Press BbC c to select the antenna input and digital channel whose signal you want to check.
Note: The physical digital channel number listed in the Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations.
Signal Meter
Signal Locked |
| ||||||||
|
|
|
|
|
| 0 | Peak 0 | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Antenna |
| 1 | |||||||
|
|
|
|
|
|
|
|
| |
Physical Digital Channel |
| 4 | |||||||
|
|
|
|
|
|
|
|
| |
Virtual Digital Channel |
| 4/1 | |||||||
Done
To close the screen and return to the Terrestrial menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
21
HM66 (E/F) Web 213:276